• Choose Language
  • Hot-rolled - Structural steel

    Hot Rolled Strip Steel

    The guaranteed strength and good weldability of our hot-rolled structural steel help ensure ease of processing and reliable end-product performance.

    As with all our hot-rolled steel products, our structural steel is manufactured under tight controls – for consistent quality that you can depend on.

    Ympress® for weight savings and component strength

    Ympress® is Tata Steel’s hot-rolled HSLA product. It is highly formable and delivers weight savings and increased component strength. The result is lighter, stronger, more consistent products.

    Ympress® adds value to automotive, lifting and excavating and shipbuilding applications, among others.

    Contact us

    Tata Steel

    PO Box 10.000

    1970 CA IJmuiden

    Netherlands

    Helpdesk

    T +31 (0)251 494191

    Overview

    Applications

    Automotive wheel rims and chassis components
    Construction and building
    Cold formed sections
    Pressure vessels
    Transport
    Tubes and pipes
    Warehouse shelving
    Lifting and excavating equipment

     

    Availability

    Structural steel products are available as follows:

    • As-rolled (+AR)
    • Normalised rolling (+N)
    • Suitable for cold forming (C)
    • Suitable for post-galvanising (Class 1)

    Relationship with standards

    Hot-rolled structural steel complies with European standard EN 10025: 2004 and is available in the grades shown in the table below.

    If normalised rolling (+N) or cold forming (C) is required, please specify when ordering. In these cases, this should be indicated by adding the relevant letter to the grade at the time of ordering (for example: S355J0C+AR). Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

    European standard

    German standards

    EN 10025-2: 2004

    DIN 17100, 1987-1

    S185+AR

    St 33

    S235JR+AR

    St 37-2

    S235J0+AR

    St 37-3U

    S235J2+N

    St 37-3N

    S235J2+AR

    -

    S275JR+AR

    St 44-2

    S275J0+AR

    St 44-3U

    S275J2+N

    St 44-3N

    S275J2+AR

    -

    S355JR+AR

    St 52-3

    S355J0+AR

    St 52-3U

    S355J2+N

    St 52-3N

    S355J2+AR

    -

    S355K2+N

    -

    S355K2+AR

    -

     

    The CE mark

    The CE mark is a symbol devised by the European Council to signify that a product meets the conditions of the applicable council directives. These conditions aim to ensure that the product is reliable and safe. Products that are “produced for incorporation in a permanent manner in construction works” fall under the Construction Products Directive. Hot-rolled steels covered by EN 10025: 2004 are used in such “works” and are therefore covered by the directive. For these products, Tata Steel’s test certificates bear the CE mark and Tata Steel has issued a certified Declaration of Conformity. All the structural products produced by Tata Steel in Europe are CE-marked except for S185+AR.

     

     

    back to top

    Properties

    Mechanical properties

    The values shown for strength and elongation in the table below are for test pieces taken transverse to the rolling direction; those for the impact test are for test pieces taken in the rolling direction.

    EN
    10025-2: 2004
    Grade

    Min. yield strength 1 2
    ReH

    Tensile strength
    Rm

     

    N/mm2

    N/mm2

     

     

     

     

     

     

    t ≤ 16

    16 < t ≤ 20

    t < 3

    3 ≤ t ≤ 20

    S185

    185

    175

    310 - 540

    290 - 510

    S235JR3

    235

    225

    360 - 510

    360 - 510

    S235J0

    235

    225

    360 - 510

    360 - 510

    S235J2

    235

    225

    360 - 510

    360 - 510

    S275JR3

    275

    265

    430 - 580

    410 - 560

    S275J0

    275

    265

    430 - 580

    410 - 560

    S275J2

    275

    265

    430 - 580

    410 - 560

    S355JR3

    355

    345

    510 - 680

    470 - 630

    S355J0

    355

    345

    510 - 680

    470 - 630

    S355J2

    355

    345

    510 - 680

    470 - 630

    S355K2

    355

    345

    510 - 680

    470 - 630

    1. Upper yield strength or 0.2% proof stress applies.
    2. For thicknesses > 16mm, the ReH value is decreased by 10 N/mm2.
    3. The impact properties of quality JR products are verified only when specified at the time of
       enquiry or order.
       Impact strengths apply to thicknesses > 6mm and are for standard test pieces only.
       For the mechanical properties of cold-forming qualities, please consult us.
    Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
    t - material thickness in mm.

     

    EN
    10025-2: 2004
    Grade

    Min elongation after fracture A

    Impact test

     

    %

     

     

     

    L0 = 80mm

     

    L0 = 5.65√S0

    Temp. °C

    Min.
    energy J

     

    1.5 < t ≤ 2

    2 < t ≤ 2.5

    2.5 < t < 3

    3 ≤ t ≤ 20

    S185

    10

    11

    12

    16

     

     

    S235JR3

    17

    18

    19

    24

    20

    27

    S235J0

    17

    18

    19

    24

    0

    27

    S235J2

    17

    18

    19

    24

    -20

    27

    S275JR3

    15

    16

    17

    21

    20

    27

    S275J0

    15

    16

    17

    21

    0

    27

    S275J2

    15

    16

    17

    21

    -20

    27

    S355JR3

    14

    15

    16

    20

    20

    27

    S355J0

    14

    15

    16

    20

    0

    27

    S355J2

    14

    15

    16

    20

    -20

    27

    S355K2

    14

    15

    16

    20

    -20

    40

    1. Upper yield strength or 0.2% proof stress applies.
    2. For thicknesses > 16mm, the ReH value is decreased by 10 N/mm2.
    3. The impact properties of quality JR products are verified only when specified at the time of
       enquiry or order.
       Impact strengths apply to thicknesses > 6mm and are for standard test pieces only.
       For the mechanical properties of cold-forming qualities, please contact us for details.
    Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
    t - material thickness in mm.

     

    Chemical composition

    Structural steel meets the requirements of the cast analysis in the standard, as shown in the table below.

    The steel grades supplied by Tata Steel are always fully killed.
    Tata Steel does not supply steel with increased copper content.

    Grade

    C

    Mn

    P

    S

    Si

    N

    Cu

     

    Max.

    Max.

    Max.

    Max.

    Max.

    Max.

    Max.

    S185

    0.55

    S235JR

    0.17

    1.40

    0.035

    0.035

    0.012

    0.55

    S235J0

    0.17

    1.40

    0.030

    0.030

    0.012

    0.55

    S235J2

    0.17

    1.40

    0.025

    0.025

    0.55

    S275JR

    0.21

    1.50

    0.035

    0.035

    0.012

    0.55

    S275J0

    0.18

    1.50

    0.030

    0.030

    0.012

    0.55

    S275J2

    0.18

    1.50

    0.025

    0.025

    0.55

    S355JR

    0.24

    1.60

    0.035

    0.035

    0.55

    0.012

    0.55

    S355J0

    0.20

    1.60

    0.030

    0.030

    0.55

    0.012

    0.55

    S355J2

    0.20

    1.60

    0.025

    0.025

    0.55

    0.55

    S355K2

    0.20

    1.60

    0.025

    0.025

    0.55

    0.55

    The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020% or if sufficient other nitrogen-binding elements are present.
    The nitrogen-binding elements shall be mentioned in the inspection document.
    For the chemical composition of cold-forming qualities, please consult us.
    The chemical composition of steels suitable for galvanising complies with EN 10025-2: 2004.
    All values are in weight%.

     

    Suitability for cold forming

    If chemistry suitable for cold forming (+C) is required, this must be specified when the material is ordered.

    Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

     

    Suitability for galvanising

    If chemistry suitable for post-galvanising (Class 1) is required, this must be specified when the material is ordered.

     

     

     

    back to top

    Dimensions

    Dimensional capability for steel produced in the Netherlands – non-pickled

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.47 - 1.49

    1300

    1300

    -

    -

    1.49 - 1.50

    1320

    1320

    1170

    -

    1.50 - 1.53

    1330

    1330

    1180

    -

    1.53 - 1.57

    1350

    1350

    1210

    960

    1.57 - 1.60

    1380

    1380

    1250

    1010

    1.60 - 1.70

    1410

    1410

    1280

    1050

    1.70 - 1.80

    1480

    1480

    1370

    1150

    1.80 - 2.00

    1550

    1550

    1440

    1230

    2.00 - 2.20

    1700

    1700

    1590

    1380

    2.20 - 2.40

    1820

    1820

    1730

    1500

    2.40 - 2.60

    1920

    1920

    1810

    1630

    2.60 - 2.70

    2030

    2030

    1880

    1710

    2.70 - 2.80

    2070

    2070

    1920

    1730

    2.80 - 3.00

    2070

    2070

    1960

    1760

    3.00 - 3.20

    2070

    2070

    2030

    1790

    3.20 - 3.50

    2070

    2070

    2070

    1840

    3.50 - 3.65

    2070

    2070

    2070

    1900

    3.65 - 4.00

    2070

    2070

    2070

    1930

    4.00 - 4.40

    2070

    2070

    2070

    2000

    4.40 - 12.70

    2070

    2070

    20702)

    2070

    12.70 - 20.00

    2070

    20701)

    2070

    20703)

    All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold rolling (C) conditions.
    The minimum width is 1000mm for thicknesses over 12.70mm.
    The minimum width is 900mm for all other thicknesses.
    1) S235 J2 available for thicknesses ≤ 12.70mm. 
    2) S275 JR/J0/J2 + N available for thicknesses ≤ 10mm.
    3) S355 JR/J0/J2/K2 + N available for thicknesses ≤ 12.70mm.
    Other dimensions are available - please contact us.

    Dimensional capability for steel produced in the UK – non-pickled

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.50 - 1.599

    1250

    1250

    1100

     -

    1.60 - 1.699

    1275

    1275

    1215

     -

    1.70 - 1.799

    1315

    1315

    1225

     -

    1.80 - 1.899

    1511

    1450

    1425

    1250

    1.90 - 1.999

    1511

    1525

    1510

    1250

    2.00 - 2.099

    1600

    1525

    1510

    1300

    2.10 - 2.199

    1600

    1550

    1510

    1300

    2.20 - 2.499

    1600

    1550

    1514

    1525

    2.50 - 2.899

    1749

    1550

    1560

    1560

    2.90 - 2.999

    1830

    1550

    1830

    1560

    3.00 - 5.000

    1830

    1830

    1830

    1830

    5.01 - 15.999

    1830

    1830

    1830

    1606

    16.00 - 16.50

    1830

    1830

    1830

     -

    All grades are available in the as-rolled (+AR) and suitable for cold rolling (C) conditions.
    The minimum width is 700mm.
    The maximum thickness for these grades in cold-forming quality is 12.5mm.

    Dimensional capability for steel produced in the Netherlands – pickled.

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.50 - 1.53

    1330

    1330

    1180

    -

    1.53 - 1.57

    1350

    1350

    1210

    960

    1.57 - 1.60

    1380

    1380

    1265

    1010

    1.60 - 1.70

    1410

    1410

    1280

    1050

    1.70 - 1.80

    1480

    1480

    1370

    1150

    1.80 - 2.00

    1550

    1550

    1440

    1230

    2.00 - 2.20

    1700

    1700

    1590

    1380

    2.20 - 2.40

    1820

    1820

    1730

    1500

    2.40 - 2.60

    1920

    1920

    1810

    1630

    2.60 - 2.70

    2030

    2030

    1880

    1710

    2.70 - 2.80

    2070

    2070

    1920

    1730

    2.80 - 3.00

    2070

    2070

    1960

    1760

    3.00 - 3.20

    2070

    2070

    2030

    1790

    3.20 - 3.47

    2070

    2070

    2070

    1840

    3.47 - 3.65

    2070

    2070

    2070

    1890

    3.65 - 4.00

    2070

    2070

    2070

    1800

    4.00 - 4.40

    2070

    2070

    2070

    1640

    4.40 - 4.83

    2070

    2070

    2070

    1490

    4.83 - 5.00

    2000

    2000

    2000

    1440

    5.00 - 5.25

    1900

    1900

    1900

    1370

    5.25 - 5.50

    1820

    1820

    1820

    1300

    5.50 - 5.80

    1720

    1720

    1720

    -

    5.80 - 6.35

    1570

    1570

    1570

    -

    All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold rolling (C) conditions.
    The minimum width is 900mm. Widths smaller than 900mm are available - please contact us.
    Thicknesses up to 20 mm may be available - please contact us.

    Dimensional capability for steel produced in the UK - pickled.

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.40 - 1.50

    1125

    1103

    1005

    1005

    1.50 - 1.60

    1260

    1250

    1265

    1100

    1.60 - 1.70

    1325

    1275

    1265

    1215

    1.70 - 1.80

    1375

    1315

    1265

    1225

    1.80 - 1.90

    1425

    1350

    1265

    1250

    1.90 - 2.00

    1500

    1450

    1350

    1350

    2.00 - 2.50

    1525

    1525

    1405

    1405

    2.50 - 5.00

    1530

    1530

    1530

    1530

    All grades are available in the as-rolled (+AR) and suitable for cold rolling (C) conditions.
    The minimum width is 735mm.

    Tolerances

    Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010 (click here).
    Tighter tolerances are available, please contact us.

     

    back to top

     

    Overview

    Overview

    Applications

    Automotive wheel rims and chassis components
    Construction and building
    Cold formed sections
    Pressure vessels
    Transport
    Tubes and pipes
    Warehouse shelving
    Lifting and excavating equipment

     

    Availability

    Structural steel products are available as follows:

    • As-rolled (+AR)
    • Normalised rolling (+N)
    • Suitable for cold forming (C)
    • Suitable for post-galvanising (Class 1)

    Relationship with standards

    Hot-rolled structural steel complies with European standard EN 10025: 2004 and is available in the grades shown in the table below.

    If normalised rolling (+N) or cold forming (C) is required, please specify when ordering. In these cases, this should be indicated by adding the relevant letter to the grade at the time of ordering (for example: S355J0C+AR). Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

    European standard

    German standards

    EN 10025-2: 2004

    DIN 17100, 1987-1

    S185+AR

    St 33

    S235JR+AR

    St 37-2

    S235J0+AR

    St 37-3U

    S235J2+N

    St 37-3N

    S235J2+AR

    -

    S275JR+AR

    St 44-2

    S275J0+AR

    St 44-3U

    S275J2+N

    St 44-3N

    S275J2+AR

    -

    S355JR+AR

    St 52-3

    S355J0+AR

    St 52-3U

    S355J2+N

    St 52-3N

    S355J2+AR

    -

    S355K2+N

    -

    S355K2+AR

    -

     

    The CE mark

    The CE mark is a symbol devised by the European Council to signify that a product meets the conditions of the applicable council directives. These conditions aim to ensure that the product is reliable and safe. Products that are “produced for incorporation in a permanent manner in construction works” fall under the Construction Products Directive. Hot-rolled steels covered by EN 10025: 2004 are used in such “works” and are therefore covered by the directive. For these products, Tata Steel’s test certificates bear the CE mark and Tata Steel has issued a certified Declaration of Conformity. All the structural products produced by Tata Steel in Europe are CE-marked except for S185+AR.

     

     

    back to top

    Properties

    Properties

    Mechanical properties

    The values shown for strength and elongation in the table below are for test pieces taken transverse to the rolling direction; those for the impact test are for test pieces taken in the rolling direction.

    EN
    10025-2: 2004
    Grade

    Min. yield strength 1 2
    ReH

    Tensile strength
    Rm

     

    N/mm2

    N/mm2

     

     

     

     

     

     

    t ≤ 16

    16 < t ≤ 20

    t < 3

    3 ≤ t ≤ 20

    S185

    185

    175

    310 - 540

    290 - 510

    S235JR3

    235

    225

    360 - 510

    360 - 510

    S235J0

    235

    225

    360 - 510

    360 - 510

    S235J2

    235

    225

    360 - 510

    360 - 510

    S275JR3

    275

    265

    430 - 580

    410 - 560

    S275J0

    275

    265

    430 - 580

    410 - 560

    S275J2

    275

    265

    430 - 580

    410 - 560

    S355JR3

    355

    345

    510 - 680

    470 - 630

    S355J0

    355

    345

    510 - 680

    470 - 630

    S355J2

    355

    345

    510 - 680

    470 - 630

    S355K2

    355

    345

    510 - 680

    470 - 630

    1. Upper yield strength or 0.2% proof stress applies.
    2. For thicknesses > 16mm, the ReH value is decreased by 10 N/mm2.
    3. The impact properties of quality JR products are verified only when specified at the time of
       enquiry or order.
       Impact strengths apply to thicknesses > 6mm and are for standard test pieces only.
       For the mechanical properties of cold-forming qualities, please consult us.
    Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
    t - material thickness in mm.

     

    EN
    10025-2: 2004
    Grade

    Min elongation after fracture A

    Impact test

     

    %

     

     

     

    L0 = 80mm

     

    L0 = 5.65√S0

    Temp. °C

    Min.
    energy J

     

    1.5 < t ≤ 2

    2 < t ≤ 2.5

    2.5 < t < 3

    3 ≤ t ≤ 20

    S185

    10

    11

    12

    16

     

     

    S235JR3

    17

    18

    19

    24

    20

    27

    S235J0

    17

    18

    19

    24

    0

    27

    S235J2

    17

    18

    19

    24

    -20

    27

    S275JR3

    15

    16

    17

    21

    20

    27

    S275J0

    15

    16

    17

    21

    0

    27

    S275J2

    15

    16

    17

    21

    -20

    27

    S355JR3

    14

    15

    16

    20

    20

    27

    S355J0

    14

    15

    16

    20

    0

    27

    S355J2

    14

    15

    16

    20

    -20

    27

    S355K2

    14

    15

    16

    20

    -20

    40

    1. Upper yield strength or 0.2% proof stress applies.
    2. For thicknesses > 16mm, the ReH value is decreased by 10 N/mm2.
    3. The impact properties of quality JR products are verified only when specified at the time of
       enquiry or order.
       Impact strengths apply to thicknesses > 6mm and are for standard test pieces only.
       For the mechanical properties of cold-forming qualities, please contact us for details.
    Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
    t - material thickness in mm.

     

    Chemical composition

    Structural steel meets the requirements of the cast analysis in the standard, as shown in the table below.

    The steel grades supplied by Tata Steel are always fully killed.
    Tata Steel does not supply steel with increased copper content.

    Grade

    C

    Mn

    P

    S

    Si

    N

    Cu

     

    Max.

    Max.

    Max.

    Max.

    Max.

    Max.

    Max.

    S185

    0.55

    S235JR

    0.17

    1.40

    0.035

    0.035

    0.012

    0.55

    S235J0

    0.17

    1.40

    0.030

    0.030

    0.012

    0.55

    S235J2

    0.17

    1.40

    0.025

    0.025

    0.55

    S275JR

    0.21

    1.50

    0.035

    0.035

    0.012

    0.55

    S275J0

    0.18

    1.50

    0.030

    0.030

    0.012

    0.55

    S275J2

    0.18

    1.50

    0.025

    0.025

    0.55

    S355JR

    0.24

    1.60

    0.035

    0.035

    0.55

    0.012

    0.55

    S355J0

    0.20

    1.60

    0.030

    0.030

    0.55

    0.012

    0.55

    S355J2

    0.20

    1.60

    0.025

    0.025

    0.55

    0.55

    S355K2

    0.20

    1.60

    0.025

    0.025

    0.55

    0.55

    The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020% or if sufficient other nitrogen-binding elements are present.
    The nitrogen-binding elements shall be mentioned in the inspection document.
    For the chemical composition of cold-forming qualities, please consult us.
    The chemical composition of steels suitable for galvanising complies with EN 10025-2: 2004.
    All values are in weight%.

     

    Suitability for cold forming

    If chemistry suitable for cold forming (+C) is required, this must be specified when the material is ordered.

    Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

     

    Suitability for galvanising

    If chemistry suitable for post-galvanising (Class 1) is required, this must be specified when the material is ordered.

     

     

     

    back to top

    Dimensions

    Dimensions

    Dimensional capability for steel produced in the Netherlands – non-pickled

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.47 - 1.49

    1300

    1300

    -

    -

    1.49 - 1.50

    1320

    1320

    1170

    -

    1.50 - 1.53

    1330

    1330

    1180

    -

    1.53 - 1.57

    1350

    1350

    1210

    960

    1.57 - 1.60

    1380

    1380

    1250

    1010

    1.60 - 1.70

    1410

    1410

    1280

    1050

    1.70 - 1.80

    1480

    1480

    1370

    1150

    1.80 - 2.00

    1550

    1550

    1440

    1230

    2.00 - 2.20

    1700

    1700

    1590

    1380

    2.20 - 2.40

    1820

    1820

    1730

    1500

    2.40 - 2.60

    1920

    1920

    1810

    1630

    2.60 - 2.70

    2030

    2030

    1880

    1710

    2.70 - 2.80

    2070

    2070

    1920

    1730

    2.80 - 3.00

    2070

    2070

    1960

    1760

    3.00 - 3.20

    2070

    2070

    2030

    1790

    3.20 - 3.50

    2070

    2070

    2070

    1840

    3.50 - 3.65

    2070

    2070

    2070

    1900

    3.65 - 4.00

    2070

    2070

    2070

    1930

    4.00 - 4.40

    2070

    2070

    2070

    2000

    4.40 - 12.70

    2070

    2070

    20702)

    2070

    12.70 - 20.00

    2070

    20701)

    2070

    20703)

    All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold rolling (C) conditions.
    The minimum width is 1000mm for thicknesses over 12.70mm.
    The minimum width is 900mm for all other thicknesses.
    1) S235 J2 available for thicknesses ≤ 12.70mm. 
    2) S275 JR/J0/J2 + N available for thicknesses ≤ 10mm.
    3) S355 JR/J0/J2/K2 + N available for thicknesses ≤ 12.70mm.
    Other dimensions are available - please contact us.

    Dimensional capability for steel produced in the UK – non-pickled

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.50 - 1.599

    1250

    1250

    1100

     -

    1.60 - 1.699

    1275

    1275

    1215

     -

    1.70 - 1.799

    1315

    1315

    1225

     -

    1.80 - 1.899

    1511

    1450

    1425

    1250

    1.90 - 1.999

    1511

    1525

    1510

    1250

    2.00 - 2.099

    1600

    1525

    1510

    1300

    2.10 - 2.199

    1600

    1550

    1510

    1300

    2.20 - 2.499

    1600

    1550

    1514

    1525

    2.50 - 2.899

    1749

    1550

    1560

    1560

    2.90 - 2.999

    1830

    1550

    1830

    1560

    3.00 - 5.000

    1830

    1830

    1830

    1830

    5.01 - 15.999

    1830

    1830

    1830

    1606

    16.00 - 16.50

    1830

    1830

    1830

     -

    All grades are available in the as-rolled (+AR) and suitable for cold rolling (C) conditions.
    The minimum width is 700mm.
    The maximum thickness for these grades in cold-forming quality is 12.5mm.

    Dimensional capability for steel produced in the Netherlands – pickled.

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.50 - 1.53

    1330

    1330

    1180

    -

    1.53 - 1.57

    1350

    1350

    1210

    960

    1.57 - 1.60

    1380

    1380

    1265

    1010

    1.60 - 1.70

    1410

    1410

    1280

    1050

    1.70 - 1.80

    1480

    1480

    1370

    1150

    1.80 - 2.00

    1550

    1550

    1440

    1230

    2.00 - 2.20

    1700

    1700

    1590

    1380

    2.20 - 2.40

    1820

    1820

    1730

    1500

    2.40 - 2.60

    1920

    1920

    1810

    1630

    2.60 - 2.70

    2030

    2030

    1880

    1710

    2.70 - 2.80

    2070

    2070

    1920

    1730

    2.80 - 3.00

    2070

    2070

    1960

    1760

    3.00 - 3.20

    2070

    2070

    2030

    1790

    3.20 - 3.47

    2070

    2070

    2070

    1840

    3.47 - 3.65

    2070

    2070

    2070

    1890

    3.65 - 4.00

    2070

    2070

    2070

    1800

    4.00 - 4.40

    2070

    2070

    2070

    1640

    4.40 - 4.83

    2070

    2070

    2070

    1490

    4.83 - 5.00

    2000

    2000

    2000

    1440

    5.00 - 5.25

    1900

    1900

    1900

    1370

    5.25 - 5.50

    1820

    1820

    1820

    1300

    5.50 - 5.80

    1720

    1720

    1720

    -

    5.80 - 6.35

    1570

    1570

    1570

    -

    All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold rolling (C) conditions.
    The minimum width is 900mm. Widths smaller than 900mm are available - please contact us.
    Thicknesses up to 20 mm may be available - please contact us.

    Dimensional capability for steel produced in the UK - pickled.

    Dimensions in mm.

    Thickness

    Max. width

    From - up to

    S185

    S235JR
    S235J0
    S235J2

    S275JR
    S275J0
    S275J2

    S355JR
    S355J0
    S355J2
    S355K2

    1.40 - 1.50

    1125

    1103

    1005

    1005

    1.50 - 1.60

    1260

    1250

    1265

    1100

    1.60 - 1.70

    1325

    1275

    1265

    1215

    1.70 - 1.80

    1375

    1315

    1265

    1225

    1.80 - 1.90

    1425

    1350

    1265

    1250

    1.90 - 2.00

    1500

    1450

    1350

    1350

    2.00 - 2.50

    1525

    1525

    1405

    1405

    2.50 - 5.00

    1530

    1530

    1530

    1530

    All grades are available in the as-rolled (+AR) and suitable for cold rolling (C) conditions.
    The minimum width is 735mm.

    Tolerances

    Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010 (click here).
    Tighter tolerances are available, please contact us.

     

    back to top