Cold-rolled

Steel for forming

Cold-rolled steel for cold forming and deep drawing is available in a range of grades. Each grade is designed for particular applications – allowing you to pick the best steel for your product.

Our forming steel is available in a choice of widths up to 2050mm and thicknesses up to 3 mm. This provides opportunities for cutting waste and maximising yield. These products are made using one of two process routes:
continuous annealing (CA)
batch annealing (BA)

Applications

  • Automotive components and body panels
  • Components for building
  • Domestic appliances
  • Electrical goods
  • Furniture
  • Radiators
  • Tubes

 

Cold-rolled coil
Cold-rolled annealing line, Port Talbot, UK
Product specification
Steel for forming is currently available in the following grades

EN-Automotive-Product-Cold-rolled-Forming-DC01 TSE

DC01
Specification details for DC01

EN-Automotive-Product-Cold-rolled-Forming-All Grades OverviewTSE

Overview

Our forming steel is available in a choice of widths up to 2050mm and thicknesses up to 3.1mm. This provides opportunities for cutting waste and maximising yield.These products are made using one of two process routes:

  • continuous annealing (CA)
  • batch annealing (BA)

Applications

Automotive components and body panels

Relationship with standards

Cold-rolled steel for forming complies with European standard EN 10130: 2006 and is available in the grades shown below.

European standard VDA
EN 10130: 2006 VDA 239-100-16
Grade Grade
DC01 CR1
DC03 CR2
DC04 CR3
DC05 CR4
DC06 CR5


Table indicates most comparable grades across standards; these are not necessarily equivalent grades.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Forming-DC01-Properties TSE

Properties

Properties


Mechanical properties

Cold-rolled steel for forming has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

EN 10130: 2006 Grade DC01
Max. yield strength Re 1,2,6 N/mm2 280
Tensile strength Rm N/mm 270 - 410
Elongation 3 % 28
r90-value 4,5   -
n90-value 4   -
1. The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point and the lower yield strength ReL for the other products.
2. For thicknesses > 0.5 mm and ≤ 0.7 mm, the value for yield strength is increased by 20 N/mm2.
   For thicknesses ≤ 0.5 mm, the value is increased by 40 N/mm2.
3. For thicknesses > 0.5 mm and ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%. For thicknesses ≤ 0.5 mm the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 =  80 mm.
4. The r- and n- values apply to a thickness of t ≥ 0.5 mm.
5. For a thickness of t > 2 mm, the r90 value or r-average value is decreased by 0.2.
6. For design purposes, a lower yield strength ReL of at least 140 N/mm2 can be assumed.
 

Chemical composition

Cold-rolled steel for forming supplied by Tata Steel comply to the following cast analysis:

EN 10130: 2006 Grade DC01
C Max. 0.12
Mn Max. 0.60
P Max. 0.045
S Max. 0.045
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Forming-DC01-Dimensions TSE

Dimensions

Dimensional capability - Continuously annealed (CA)

Dimensions in mm.

Thickness Max. width
From - up to DC01
0.37 - 0.45 1390
0.45 - 0.50 1470
0.50 - 0.60 1550
0.60 - 0.75 1710
0.75 - 1.60 1820
1.60 - 1.70 1750
1.70 - 1.80 1650
1.80 - 1.90 1525
1.90 - 1.95 1520
1.95 - 2.00 1500
Minimum width is 900 mm for thicknesses below 0.5 mm.
Minimum width is 825 mm for all other thicknesses.
 

Dimensional capability – Batch annealed (BA)

Dimensions in mm.

Thickness Max. width
From - up to DC01
0.35 - 0.37 1300
0.37 - 0.40 1630
0.40 - 0.50 1690
0.50 - 0.70 1920
0.70 - 0.80 1970
0.80 - 1.00 2030
1.00 - 2.40 2030
2.40 - 2.50 1960
2.50 - 2.60 1940
2.60 - 2.70 1920
2.70 - 2.80 1850
2.80 - 2.90 1790
2.90 - 3.00 1730
The minimum width is 710 mm.
Other dimensions may be available – please contact us.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Automotive-Product-Cold-rolled-Forming-DC03 TSE

DC03
Specification details for DC03

EN-Automotive-Product-Cold-rolled-Forming-All Grades OverviewTSE

Overview

Our forming steel is available in a choice of widths up to 2050mm and thicknesses up to 3.1mm. This provides opportunities for cutting waste and maximising yield.These products are made using one of two process routes:

  • continuous annealing (CA)
  • batch annealing (BA)

Applications

Automotive components and body panels

Relationship with standards

Cold-rolled steel for forming complies with European standard EN 10130: 2006 and is available in the grades shown below.

European standard VDA
EN 10130: 2006 VDA 239-100-16
Grade Grade
DC01 CR1
DC03 CR2
DC04 CR3
DC05 CR4
DC06 CR5


Table indicates most comparable grades across standards; these are not necessarily equivalent grades.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Forming-DC03-Properties TSE

Properties

Properties


Mechanical properties

Cold-rolled steel for forming has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

EN 10130: 2006 Grade DC03
Max. yield strength Re 1,2,6 N/mm2 240
Tensile strength Rm N/mm 270 - 370
Elongation 3 % 34
r90-value 4,5   1.3
n90-value 4   -
1. The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point and the lower yield strength ReL for the other products.
2. For thicknesses > 0.5 mm and ≤ 0.7 mm, the value for yield strength is increased by 20 N/mm2.
   For thicknesses ≤ 0.5 mm, the value is increased by 40 N/mm2.
3. For thicknesses > 0.5 mm and ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%. For thicknesses ≤ 0.5 mm the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 =  80 mm.
4. The r- and n- values apply to a thickness of t ≥ 0.5 mm.
5. For a thickness of t > 2 mm, the r90 value or r-average value is decreased by 0.2.
6. For design purposes, a lower yield strength ReL of at least 140 N/mm2 can be assumed.

Chemical composition

Cold-rolled steel for forming supplied by Tata Steel comply to the following cast analysis:

EN 10130: 2006 Grade DC03
C Max. 0.10
Mn Max. 0.45
P Max. 0.035
S Max. 0.035
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Forming-DC03-Dimensions TSE

Dimensions

Dimensional capability - Continuously annealed (CA)

Dimensions in mm.

Thickness Max. width
From - up to DC03
0.50 - 0.55 1400
0.55 - 0.60 1510
0.60 - 0.65 1600
0.65 - 0.70 1635
0.70 - 0.75 1650
0.75 - 1.60 1815
1.60 - 1.70 1750
1.70 - 1.80 1650
1.80 - 1.90 1525
1.90 - 2.00 1500
Minimum width is 825 mm.
 

Dimensional capability – Batch annealed (BA)

Dimensions in mm.

Thickness Max. width
From - up to DC03
0.35 - 0.37 1300
0.37 - 0.40 1530
0.40 - 0.50 1680
0.50 - 0.60 1750
0.60 - 0.70 1790
0.70 - 0.80 1830
0.80 - 0.90 1880
0.90 - 1.00 1920
1.00 - 1.10 1970
1.10 - 1.20 2020
1.20 - 1.90 2030
1.90 - 2.00 1960
2.00 - 2.20 1840
2.20 - 2.40 1700
2.40 - 2.60 1570
2.60 - 3.00 1500
The minimum width is 710 mm.
Other dimensions may be available – please contact us.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Automotive-Product-Cold-rolled-Forming-DC04 TSE

DC04
Specification details for DC04

EN-Automotive-Product-Cold-rolled-Forming-All Grades OverviewTSE

Overview

Our forming steel is available in a choice of widths up to 2050mm and thicknesses up to 3.1mm. This provides opportunities for cutting waste and maximising yield.These products are made using one of two process routes:

  • continuous annealing (CA)
  • batch annealing (BA)

Applications

Automotive components and body panels

Relationship with standards

Cold-rolled steel for forming complies with European standard EN 10130: 2006 and is available in the grades shown below.

European standard VDA
EN 10130: 2006 VDA 239-100-16
Grade Grade
DC01 CR1
DC03 CR2
DC04 CR3
DC05 CR4
DC06 CR5


Table indicates most comparable grades across standards; these are not necessarily equivalent grades.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Forming-DC04-Properties TSE

Properties

Properties


Mechanical properties

Cold-rolled steel for forming has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

EN 10130: 2006 Grade DC04
Max. yield strength Re 1,2,6 N/mm2 210
Tensile strength Rm N/mm 270 - 350
Elongation 3 % 38
r90-value 4,5   1.6
n90-value 4   0.180
1. The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point and the lower yield strength ReL for the other products.
2. For thicknesses > 0.5 mm and ≤ 0.7 mm, the value for yield strength is increased by 20 N/mm2.
   For thicknesses ≤ 0.5 mm, the value is increased by 40 N/mm2.
3. For thicknesses > 0.5 mm and ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%. For thicknesses ≤ 0.5 mm the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 =  80 mm.
4. The r- and n- values apply to a thickness of t ≥ 0.5 mm.
5. For a thickness of t > 2 mm, the r90 value or r-average value is decreased by 0.2.
6. For design purposes, a lower yield strength ReL of at least 140 N/mm2 can be assumed.
 

Chemical composition

Cold-rolled steel for forming supplied by Tata Steel comply to the following cast analysis:

EN 10130: 2006 Grade DC04
C Max. 0.08
Mn Max. 0.40
P Max. 0.030
S Max. 0.030
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Forming-DC04-Dimensions TSE

Dimensions

Dimensional capability - Continuously annealed (CA)

Dimensions in mm.

Thickness Max. width
From - up to DC04
0.50 - 0.60 1450
0.60 - 0.65 1600
0.65 - 0.70 1650
0.70 - 0.78 1700
0.78 - 1.60 1785
1.60 - 1.70 1750
1.70 - 1.80 1650
1.80 - 1.90 1525
1.90 - 2.00 1500
Minimum width is 825 mm.
 

Dimensional capability – Batch annealed (BA)

Dimensions in mm.

Thickness Max. width
From - up to DC04
0.35 - 0.37 1300
0.37 - 0.40 1530
0.40 - 0.50 1680
0.50 - 0.60 1750
0.60 - 0.70 1790
0.70 - 0.80 1830
0.80 - 0.90 1880
0.90 - 1.00 1920
1.00 - 1.10 1970
1.10 - 1.20 2020
1.20 - 1.90 2030
1.90 - 2.00 1960
2.00 - 2.20 1840
2.20 - 2.40 1700
2.40 - 2.60 1570
2.60 - 3.00 1500
The minimum width is 710 mm.
Other dimensions may be available – please contact us.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Automotive-Product-Cold-rolled-Forming-DC05 TSE

DC05
Specification details for DC05

EN-Automotive-Product-Cold-rolled-Forming-All Grades OverviewTSE

Overview

Our forming steel is available in a choice of widths up to 2050mm and thicknesses up to 3.1mm. This provides opportunities for cutting waste and maximising yield.These products are made using one of two process routes:

  • continuous annealing (CA)
  • batch annealing (BA)

Applications

Automotive components and body panels

Relationship with standards

Cold-rolled steel for forming complies with European standard EN 10130: 2006 and is available in the grades shown below.

European standard VDA
EN 10130: 2006 VDA 239-100-16
Grade Grade
DC01 CR1
DC03 CR2
DC04 CR3
DC05 CR4
DC06 CR5


Table indicates most comparable grades across standards; these are not necessarily equivalent grades.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Forming-DC05-Properties TSE

Properties

Properties


Mechanical properties

Cold-rolled steel for forming has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

EN 10130: 2006 Grade DC05
Max. yield strength Re 1,2,6 N/mm2 180
Tensile strength Rm N/mm 270 - 330
Elongation 3 % 40
r90-value 4,5   1.9
n90-value 4   0.200
1. The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point and the lower yield strength ReL for the other products.
2. For thicknesses > 0.5 mm and ≤ 0.7 mm, the value for yield strength is increased by 20 N/mm2.
   For thicknesses ≤ 0.5 mm, the value is increased by 40 N/mm2.
3. For thicknesses > 0.5 mm and ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%. For thicknesses ≤ 0.5 mm the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 =  80 mm.
4. The r- and n- values apply to a thickness of t ≥ 0.5 mm.
5. For a thickness of t > 2 mm, the r90 value or r-average value is decreased by 0.2.
6. For design purposes, a lower yield strength ReL of at least 140 N/mm2 can be assumed.
 

Chemical composition

Cold-rolled steel for forming supplied by Tata Steel comply to the following cast analysis:

EN 10130: 2006 Grade DC05
C Max. 0.06
Mn Max. 0.35
P Max. 0.025
S Max. 0.025
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Forming-DC05-Dimensions TSE

Dimensions

Dimensional capability - Continuously annealed (CA)

Dimensions in mm.

Thickness Max. width
From - up to DC05
0.50 - 0.60 1450
0.60 - 0.65 1600
0.65 - 0.70 1650
0.70 - 0.78 1700
0.78 - 1.60 1785
Minimum width is 825 mm for all other thicknesses.
 

Dimensional capability – Batch annealed (BA)

Dimensions in mm.

Thickness Max. width
From - up to DC05
0.35 - 0.40 1300
0.40 - 0.50 1760
0.50 - 0.60 1840
0.60 - 0.70 1880
0.70 - 0.80 1920
0.80 - 0.90 1970
0.90 - 1.00 2020
1.00 - 1.30 2030
1.30 - 1.60 1880
1.60 - 1.80 1730
1.80 - 2.00 1570
2.00 - 2.20 1430
2.20 - 2.40 1310
2.40 - 2.50 1300
The minimum width is 710 mm.
Other dimensions may be available – please contact us.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Automotive-Product-Cold-rolled-Forming-DC06 TSE

DC06
Specification details for DC06

EN-Automotive-Product-Cold-rolled-Forming-All Grades OverviewTSE

Overview

Our forming steel is available in a choice of widths up to 2050mm and thicknesses up to 3.1mm. This provides opportunities for cutting waste and maximising yield.These products are made using one of two process routes:

  • continuous annealing (CA)
  • batch annealing (BA)

Applications

Automotive components and body panels

Relationship with standards

Cold-rolled steel for forming complies with European standard EN 10130: 2006 and is available in the grades shown below.

European standard VDA
EN 10130: 2006 VDA 239-100-16
Grade Grade
DC01 CR1
DC03 CR2
DC04 CR3
DC05 CR4
DC06 CR5


Table indicates most comparable grades across standards; these are not necessarily equivalent grades.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Forming-DC06-Properties TSE

Properties

Properties


Mechanical properties

Cold-rolled steel for forming has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

EN 10130: 2006 Grade DC06
Max. yield strength Re 1,2,6 N/mm2 170
Tensile strength Rm N/mm 270 - 330
Elongation 3 % 41
r90-value 4,5   2.1
n90-value 4   0.220
1. The values of the yield strength are those of the 0.2% yield strength for products with no definite yield point and the lower yield strength ReL for the other products.
2. For thicknesses > 0.5 mm and ≤ 0.7 mm, the value for yield strength is increased by 20 N/mm2.
   For thicknesses ≤ 0.5 mm, the value is increased by 40 N/mm2.
3. For thicknesses > 0.5 mm and ≤ 0.7 mm the minimum elongation after fracture is decreased by 2%. For thicknesses ≤ 0.5 mm the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 =  80 mm.
4. The r- and n- values apply to a thickness of t ≥ 0.5 mm.
5. For a thickness of t > 2 mm, the r90 value or r-average value is decreased by 0.2.
6. For design purposes, a lower yield strength ReL of at least 120 N/mm2 can be assumed.
 

Chemical composition

Cold-rolled steel for forming supplied by Tata Steel comply to the following cast analysis:

EN 10130: 2006 Grade DC06
C Max. 0.02
Mn Max. 0.25
P Max. 0.020
S Max. 0.020
Ti  1 Max. 0.30
1. Titanium may be replaced by niobium. Carbon and nitrogen will be completely bound.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Forming-DC06-Dimensions TSE

Dimensions

Dimensional capability - Continuously annealed (CA)

Dimensions in mm.

Thickness Max. width
From - up to DC06
0.50 - 0.60 1450
0.60 - 0.65 1600
0.65 - 0.70 1650
0.70 - 0.78 1700
0.78 - 1.20 1785
Minimum width is 825 mm.
 

Dimensional capability – Batch annealed (BA)

Dimensions in mm.

Thickness Max. width
From - up to DC06
0.50 - 0.60 1900
0.60 - 0.70 2010
0.70 - 1.50 2030
1.50 - 1.60 1920
1.60 - 1.70 1800
1.70 - 1.80 1720
1.80 - 1.90 1600
1.90 - 2.00 1550
2.00 - 2.10 1490
2.10 - 2.20 1420
The minimum width is 710 mm.
Other dimensions may be available – please contact us.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.