Tolerances on thickness
The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:
Thickness tolerance |
Availability |
---|---|
Full thickness tolerance |
Available |
Special thickness tolerance |
Available |
50% of full thickness tolerance |
Refer before ordering |
The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².
Nominal |
Normal tolerances for a nominal width of 1 2 |
Special tolerances (S) for a |
|||||
---|---|---|---|---|---|---|---|
|
≤ 1200 |
> 1200 |
> 1500 |
≤ 1200 |
> 1200 |
> 1500 |
|
|
≤ 1500 |
|
|
≤ 1500 |
|
||
> 0.40 |
≤ 0.60 |
± 0.04 |
± 0.05 |
± 0.06 |
± 0.035 |
± 0.040 |
± 0.045 |
> 0.60 |
≤ 0.80 |
± 0.05 |
± 0.06 |
± 0.07 |
± 0.040 |
± 0.045 |
± 0.050 |
> 0.80 |
≤ 1.00 |
± 0.06 |
± 0.07 |
± 0.08 |
± 0.045 |
± 0.050 |
± 0.060 |
> 1.00 |
≤ 1.20 |
± 0.07 |
± 0.08 |
± 0.09 |
± 0.050 |
± 0.060 |
± 0.070 |
> 1.20 |
≤ 1.60 |
± 0.10 |
± 0.11 |
± 0.12 |
± 0.060 |
± 0.070 |
± 0.080 |
> 1.60 |
≤ 2.00 |
± 0.12 |
± 0.13 |
± 0.14 |
± 0.070 |
± 0.080 |
± 0.090 |
> 2.00 |
≤ 2.50 |
± 0.14 |
± 0.15 |
± 0.16 |
± 0.090 |
± 0.100 |
± 0.110 |
> 2.50 |
≤ 3.00 |
± 0.17 |
± 0.17 |
± 0.18 |
± 0.110 |
± 0.120 |
± 0.130 |
> 3.00 |
≤ 5.00 |
± 0.20 |
± 0.20 |
± 0.21 |
± 0.15 |
± 0.16 |
± 0.17 |
> 5.00 |
≤ 6.50 |
± 0.22 |
± 0.22 |
± 0.23 |
± 0.17 |
± 0.18 |
± 0.19 |
1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.
The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm² ≤ Rp0.2 < 360N/mm² and for grades DX51D and S550GD.
Nominal |
Normal tolerances for a nominal width of 1 2 |
Special tolerances (S) for a |
|||||
---|---|---|---|---|---|---|---|
|
≤ 1200 |
> 1200 |
> 1500 |
≤ 1200 |
> 1200 |
> 1500 |
|
|
≤ 1500 |
|
|
≤ 1500 |
|
||
≥ 0.35 |
≤ 0.40 |
± 0.05 |
± 0.06 |
- |
± 0.035 |
± 0.040 |
- |
> 0.40 |
≤ 0.60 |
± 0.05 |
± 0.06 |
± 0.07 |
± 0.040 |
± 0.045 |
± 0.050 |
> 0.60 |
≤ 0.80 |
± 0.06 |
± 0.07 |
± 0.08 |
± 0.045 |
± 0.050 |
± 0.060 |
> 0.80 |
≤ 1.00 |
± 0.07 |
± 0.08 |
± 0.09 |
± 0.050 |
± 0.060 |
± 0.070 |
> 1.00 |
≤ 1.20 |
± 0.08 |
± 0.09 |
± 0.11 |
± 0.060 |
± 0.070 |
± 0.080 |
> 1.20 |
≤ 1.60 |
± 0.11 |
± 0.13 |
± 0.14 |
± 0.070 |
± 0.080 |
± 0.090 |
> 1.60 |
≤ 2.00 |
± 0.14 |
± 0.15 |
± 0.16 |
± 0.080 |
± 0.090 |
± 0.110 |
> 2.00 |
≤ 2.50 |
± 0.16 |
± 0.17 |
± 0.18 |
± 0.110 |
± 0.120 |
± 0.130 |
> 2.50 |
≤ 3.00 |
± 0.19 |
± 0.20 |
± 0.20 |
± 0.130 |
± 0.140 |
± 0.150 |
> 3.00 |
≤ 5.00 |
± 0.22 |
± 0.24 |
± 0.25 |
± 0.17 |
± 0.18 |
± 0.19 |
> 5.00 |
≤ 6.50 |
± 0.24 |
± 0.25 |
± 0.26 |
± 0.19 |
± 0.20 |
± 0.21 |
1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm
The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ Rp0.2 ≤ 420N/mm².
Nominal |
Normal tolerances for a nominal width of 1 2 |
Special tolerances (S) for a |
|||||
---|---|---|---|---|---|---|---|
|
≤ 1200 |
> 1200 |
> 1500 |
≤ 1200 |
> 1200 |
> 1500 |
|
|
≤ 1500 |
|
|
≤ 1500 |
|
||
≥ 0.35 |
≤ 0.40 |
± 0.05 |
± 0.06 |
- |
± 0.040 |
± 0.045 |
- |
> 0.40 |
≤ 0.60 |
± 0.06 |
± 0.07 |
± 0.08 |
± 0.045 |
± 0.050 |
± 0.060 |
> 0.60 |
≤ 0.80 |
± 0.07 |
± 0.08 |
± 0.09 |
± 0.050 |
± 0.060 |
± 0.070 |
> 0.80 |
≤ 1.00 |
± 0.08 |
± 0.09 |
± 0.11 |
± 0.060 |
± 0.070 |
± 0.080 |
> 1.00 |
≤ 1.20 |
± 0.10 |
± 0.11 |
± 0.12 |
± 0.070 |
± 0.080 |
± 0.090 |
> 1.20 |
≤ 1.60 |
± 0.13 |
± 0.14 |
± 0.16 |
± 0.080 |
± 0.090 |
± 0.110 |
> 1.60 |
≤ 2.00 |
± 0.16 |
± 0.17 |
± 0.19 |
± 0.090 |
± 0.110 |
± 0.120 |
> 2.00 |
≤ 2.50 |
± 0.18 |
± 0.20 |
± 0.21 |
± 0.120 |
± 0.130 |
± 0.140 |
> 2.50 |
≤ 3.00 |
± 0.22 |
± 0.22 |
± 0.23 |
± 0.140 |
± 0.150 |
± 0.160 |
> 3.00 |
≤ 5.00 |
± 0.22 |
± 0.24 |
± 0.25 |
± 0.17 |
± 0.18 |
± 0.19 |
> 5.00 |
≤ 6.50 |
± 0.24 |
± 0.25 |
± 0.26 |
± 0.19 |
± 0.20 |
± 0.21 |
1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.
The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < Rp0.2 ≤ 900N/mm².
Nominal |
Normal tolerances for a nominal width of 1 2 |
Special tolerances (S) for a |
|||||
---|---|---|---|---|---|---|---|
|
≤ 1200 |
> 1200 |
> 1500 |
≤ 1200 |
> 1200 |
> 1500 |
|
|
≤ 1500 |
|
|
≤ 1500 |
|
||
≥ 0.35 |
≤ 0.40 |
± 0.06 |
± 0.07 |
- |
± 0.045 |
± 0.050 |
- |
> 0.40 |
≤ 0.60 |
± 0.06 |
± 0.08 |
± 0.09 |
± 0.050 |
± 0.060 |
± 0.070 |
> 0.60 |
≤ 0.80 |
± 0.07 |
± 0.09 |
± 0.11 |
± 0.060 |
± 0.070 |
± 0.080 |
> 0.80 |
≤ 1.00 |
± 0.09 |
± 0.11 |
± 0.12 |
± 0.070 |
± 0.080 |
± 0.090 |
> 1.00 |
≤ 1.20 |
± 0.11 |
± 0.13 |
± 0.14 |
± 0.080 |
± 0.090 |
± 0.110 |
> 1.20 |
≤ 1.60 |
± 0.15 |
± 0.16 |
± 0.18 |
± 0.090 |
± 0.110 |
± 0.120 |
> 1.60 |
≤ 2.00 |
± 0.18 |
± 0.19 |
± 0.21 |
± 0.110 |
± 0.120 |
± 0.140 |
> 2.00 |
≤ 2.50 |
± 0.21 |
± 0.22 |
± 0.24 |
± 0.140 |
± 0.150 |
± 0.170 |
> 2.50 |
≤ 3.00 |
± 0.24 |
± 0.25 |
± 0.26 |
± 0.170 |
± 0.180 |
± 0.190 |
> 3.00 |
≤ 5.00 |
± 0.26 |
± 0.27 |
± 0.28 |
± 0.23 |
± 0.24 |
± 0.26 |
> 5.00 |
≤ 6.50 |
± 0.28 |
± 0.29 |
± 0.30 |
± 0.25 |
± 0.26 |
± 0.28 |
1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.
Tolerances on width
The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.
Tolerances in mm.
Nominal width w | Normal tolerances | Special tolerances (S) |
---|---|---|
600 ≤ w ≤ 1200 | + 5 0 |
+ 2 0 |
1200 < w ≤ 1500 | + 6 0 |
+ 2 0 |
1500 < w ≤ 1800 | + 7 0 |
+ 3 0 |
w > 1800 | + 8 0 |
+ 3 0 |
Dimensions and coil weights
Description | Availability |
---|---|
Coil diameter inner | 610mm |
(508 mm available on request) | |
Coil diameter outer | 10/7 x width max |
1000mm min. | |
2500mm max. | |
Coil weight | 30t max. |
33t max available after consultation | |
Coil weight limited by maximum outer diameter | |
Maximum weight allowed by road/rail transport | |
Some products may have different coil weight ranges available | |
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested | |
KIM: width ≤ 1200 mm | 11.7 - 22.7 kg/mm width |
KIM: 1200mm < width ≤ 1700 mm | 11.6 - 21.7 kg/mm width |
KIM: width > 1700 mm | 11.0 kg/mm width and 11.6 - 21.7 kg/mm width |
Minimum tonnage per order | Refer to price list for order quantity details |
Minimum order quantities may apply |