Hot-rolled

Steel for forming

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications

The consistent quality of Tata Steel's forming grades ensures reliable processing.  All of our forming grades have a low carbon content for excellent welding performance.

DS type B WR is particularly suitable for use in wheel rims because of its low aluminium content and controlled Mn:Si ratio. The low carbon content gives DS type B WR excellent welding performance.


 

Abrasion resistant wear steel
Product specification
Steel for forming is currently available in the following grades

EN_US-Engineering-Product-Hot-Rolled-Forming-CS TYPE A TSE

CS Type A
Specification details for CS TYPE A

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-CS TYPE A-Properties TSE

Properties

Properties


Mechanical properties

The typical values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction:

Grade ASTM A1011-15 CS Type A
Yield strength ksi 30 - 50
Elongation % 25
Min. elongation after fracture A uses test piece length L0 = 2 inches.
ASTM A1018 and SAE have no mechanical property requirements. When ordering combined ASTM / SAE specifications, the ASTM mechanical properties apply.

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.

ASTM A1011-15
ASTM A1018-16
SAE
Grade CS type A SAE 1008 CS Type A/SAE 1008
C Max. 0.10 0.10 0.10
Mn Max. 0.60 0.50 0.50
P Max. 0.030 0.030 0.030
S Max. 0.035 0.035 0.035
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-CS TYPE ABC DS TYPE B-Dimensions TSE

Dimensions

Dimensions

Steel for forming is available in the following dimensions.
Dimensions in inches.

Thickness Max. width
From - up to Non-Pickled 3 Pickled 3
0.058 - 0.060 51 51
0.060 - 0.070 53 53
0.070 - 0.080 61 61
0.080 - 0.090 68 68
0.090 - 0.100 73 73
0.100 - 0.110 79 79
0.110 - 0.150 81 81
0.150 - 0.200 81 74
0.200 - 0.230 81 64
0.230 1 - 0.300 81 -
0.300 1 - 0.400 81 -
0.400 1 - 0.500 2 81 -
The minimum width is 27.5 inch.
1 Dimensions specified in ASTM A1018.
2 Maximum width for thickness > 0.500 inch on request.
3 For DS Type B boron added in thicknesses up to 0.080 inch, the maximum width is reduced by 8 inch.

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

 

EN_US-Engineering-Product-Hot-Rolled-Forming-DS TYPE A TSE

DS Type A
Specification details for DS Type A

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-DS TYPE A-Properties TSN

Properties

Properties


Mechanical properties

The typical values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction:

Grade ASTM A1011-15 DS Type A
Yield strength ksi 30 - 45
Elongation % 28
Min. elongation after fracture A uses test piece lenghth L0 = 2 inches.
ASTM A1018 and SAE have no mechanical property requirements. When ordering combined ASTM / SAE specifications, the ASTM mechanical properties apply.

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.

ASTM A1011-15
ASTM A1018-16
SAE
Grade DS Type A SAE 1006 DS Type A/SAE 1006
C Max. 0.080 0.080 0.080
Mn Max. 0.50 0.40 0.40
P Max. 0.020 0.030 0.020
S Max. 0.030 0.035 0.030
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-CS TYPE ABC DS TYPE B-Dimensions TSE

Dimensions

Dimensions

Steel for forming is available in the following dimensions.
Dimensions in inches.

Thickness Max. width
From - up to Non-Pickled 3 Pickled 3
0.058 - 0.060 51 51
0.060 - 0.070 53 53
0.070 - 0.080 61 61
0.080 - 0.090 68 68
0.090 - 0.100 73 73
0.100 - 0.110 79 79
0.110 - 0.150 81 81
0.150 - 0.200 81 74
0.200 - 0.230 81 64
0.230 1 - 0.300 81 -
0.300 1 - 0.400 81 -
0.400 1 - 0.500 2 81 -
The minimum width is 27.5 inch.
1 Dimensions specified in ASTM A1018.
2 Maximum width for thickness > 0.500 inch on request.
3 For DS Type B boron added in thicknesses up to 0.080 inch, the maximum width is reduced by 8 inch.

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

 

EN_US-Engineering-Product-Hot-Rolled-Forming-DS TYPE B TSE

DS TYPE B
Specification details for DS TYPE B

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-DS TYPE B-Properties TSE

Properties

Properties


Mechanical properties

The typical values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction:

Grade ASTM A1011-15 DS Type B
Yield strength ksi 30 - 45
Elongation % 28
Min. elongation after fracture A uses test piece length L0 = 2 inches.
ASTM A1018 and SAE have no mechanical property requirements. When ordering combined ASTM / SAE specifications, the ASTM mechanical properties apply.
 

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.
Maximum values unless otherwise shown.

ASTM A1011-15
ASTM A1018-16
SAE
Grade DS Type B SAE 1006 DS Type B/SAE 1006
C Max. 0.02 - 0.08 0.08 0.02 - 0.08
Mn Max. 0.50 0.40 0.40
P Max. 0.020 0.030 0.020
S Max. 0.030 0.035 0.030
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-CS TYPE ABC DS TYPE B-Dimensions TSE

Dimensions

Dimensions

Steel for forming is available in the following dimensions.
Dimensions in inches.

Thickness Max. width
From - up to Non-Pickled 3 Pickled 3
0.058 - 0.060 51 51
0.060 - 0.070 53 53
0.070 - 0.080 61 61
0.080 - 0.090 68 68
0.090 - 0.100 73 73
0.100 - 0.110 79 79
0.110 - 0.150 81 81
0.150 - 0.200 81 74
0.200 - 0.230 81 64
0.230 1 - 0.300 81 -
0.300 1 - 0.400 81 -
0.400 1 - 0.500 2 81 -
The minimum width is 27.5 inch.
1 Dimensions specified in ASTM A1018.
2 Maximum width for thickness > 0.500 inch on request.
3 For DS Type B boron added in thicknesses up to 0.080 inch, the maximum width is reduced by 8 inch.

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1012 TSE

ASTM A568 1012
Specification details for ASTM A568 1012

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568-Properties TSN

Properties

Properties


Mechanical properties

ASTM A568 has no mechanical property requirements

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.

ASTM A568 Grade 1012 1016 1018 1022
C Max. 0.10-0.15 0.13-0.18 0.15-0.20 0.18-0.23
Mn Max. 0.3-0.6 0.6-0.9 0.6-0.9 0.7-1.0
P Max. 0.030 0.030 0.030 0.030
S Max. 0.035 0.035 0.035 0.035
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1012-Dimensions TSN

Dimensions

Dimensions

ASTM A568 1012 is available in the following dimensions.
Dimensions in inches.

Thickness Max width
From Up to Non Pickled Pickled
0.058 0.070 49 49
0.070 0.080 60 60
0.080 0.110 62 60
0.110 0.200 72 60
0.200 0.650 72 -
Minimum width is 36 inch.

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1016 TSE

ASTM A568 1016
Specification details for ASTM A568 1016

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568-Properties TSN

Properties

Properties


Mechanical properties

ASTM A568 has no mechanical property requirements

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.

ASTM A568 Grade 1012 1016 1018 1022
C Max. 0.10-0.15 0.13-0.18 0.15-0.20 0.18-0.23
Mn Max. 0.3-0.6 0.6-0.9 0.6-0.9 0.7-1.0
P Max. 0.030 0.030 0.030 0.030
S Max. 0.035 0.035 0.035 0.035
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1016-Dimensions TSN

Dimensions

Dimensions

ASTM A568 1016 is available in the following dimensions.
Dimensions in inches.

Thickness Max Width
From Up to Non Pickled Pickled
0.058 0.070 49 49
0.070 0.090 55 55
0.090 0.200 55 55
0.200 0.650 63 -
Minimum width is 36 inch.
 

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1018 TSE

ASTM A568 1018
Specification details for ASTM A568 10182

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568-Properties TSN

Properties

Properties


Mechanical properties

ASTM A568 has no mechanical property requirements

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.

ASTM A568 Grade 1012 1016 1018 1022
C Max. 0.10-0.15 0.13-0.18 0.15-0.20 0.18-0.23
Mn Max. 0.3-0.6 0.6-0.9 0.6-0.9 0.7-1.0
P Max. 0.030 0.030 0.030 0.030
S Max. 0.035 0.035 0.035 0.035
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1018-Dimensions TSN

Dimensions

Dimensions

ASTM A568 1018 is available in the following dimensions.
Dimensions in inches.

Thickness Max width
From Up to Non Pickled Pickled
0.070 0.080 51 51
0.080 0.090 60 60
0.090 0.110 61 60
0.110 0.200 63 60
0.200 0.600 63 -
The minimum width is 36 inch.

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1022 TSE

ASTM A568 1022
Specification details for ASTM A568 1022

EN_US-Engineering-Product-Hot-Rolled-Forming-All grades OverviewTSE

Overview

Overview
 

Hot-rolled steel for cold forming is used for bending and deep drawing in a wide range of applications.The consistent quality of Tata Steel's forming grades ensures reliable processing. All of our forming grades have a low carbon content for excellent welding performance.

Applications

  • Automotive components
  • Domestic appliance components
  • Furniture
  • Switch gear panels
  • Tubes and sections
  • Wheel rims


Relationship with standards

Tata Steel offers hot-rolled steel for forming in grades that comply with ASTM standards as shown in the table below.
All grades are available in qualities suitable for galvanizing.

ASTM SAE JIS
ASTM A1011-15   JIS G3131
ASTM A1018-16 1    
CS type A SAE 1008  
CS type B SAE 1010 SPHC
    SPHD
CS type B SAE 1012  
DS type A SAE 1006  
DS type B 2 SAE 1006 SPHE
- SAE 1006 B added -
- - SPHF
ASTM A518 SAE JIS
1012 - -
1016 - -
1018 - -
1022 - -

1. ASTM A1011 covers grades below 0.230 inch. ASTM A1018 covers grades greater than or equal to 0.230 inch.
2. DS type B also available with boron addition.
3. Not in ASTM A1011 or ASTM A1018 . Tata Steel’s own specification.

EN_US-Engineering-Product-Hot-rolled-All Grades Surface aspects Supply ConditionsTSE

Supply conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
 
Trimmed edges available in thicknesses up to 0.25 inch.
The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs. You can find details on how to get in touch with us in 'Contact Us' below.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling or preservative oil applied. 
Oil weight normally 55 - 275 mg/ft2

Alternative oiling ranges are available.
Please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568-Properties TSN

Properties

Properties


Mechanical properties

ASTM A568 has no mechanical property requirements

Chemical composition

Hot-rolled steel for forming meets the requirements of the heat analysis in the standard as shown in the table below.

ASTM A568 Grade 1012 1016 1018 1022
C Max. 0.10-0.15 0.13-0.18 0.15-0.20 0.18-0.23
Mn Max. 0.3-0.6 0.6-0.9 0.6-0.9 0.7-1.0
P Max. 0.030 0.030 0.030 0.030
S Max. 0.035 0.035 0.035 0.035
All values are in weight%.

EN_US-Engineering-Product-Hot-Rolled-Forming-ASTM A568 1022-Dimensions TSN

Dimensions

Dimensions

ASTM A568 1022 is available in the following dimensions.
Dimensions in inches.

Thickness Max Width
From Up to Non Pickled Pickled
0.070 0.080 51 51
0.080 0.090 60 60
0.090 0.110 61 60
0.110 0.200 63 60
0.200 0.600 63 -
The minimum width is 36 inch.

Tolerances on thickness

Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2007.
Tighter tolerances are available, please contact us. Tolerances are over, no under.

 

EN_US-Engineering-Product-Hot-rolled-All grades Shape and dimensional tolerancesTSE

Shape and dimensional tolerances

Shape and dimensional tolerances

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in ASTM A568: 2015 / A635: 2015.
Thickness tolerances over, no tolerance under.
Tighter tolerances are available as shown below:

Carbon Steel Thickness tolerances available
ASTM A 568 (2015) / A635 (2015)
20 - 40 40 - 48 48 - 60 60 - 72 >72
0.031 - 0.051 0.01 0.01 0.01 0.01 0.01
0.051 - 0.057 0.01 0.012 0.012 0.014 0.014
0.057 - 0.071 0.012 0.012 0.014 0.014 0.014
0.071 - 0.098 0.014 0.014 0.014 0.016 0.016
0.098 - 0.179 0.014 0.016 0.016 0.016 0.016
0.179 - 0.229 0.016 0.018 0.02 0.022 0.024
0.229 - 0.313 0.022 0.024 0.024 0.026 0.03
0.313 - 0.375 0.024 0.026 0.028 0.03 0.032
0.375 - 0.500 0.028 0.028 0.03 0.032 0.036
0.500 - 0.625 0.03 0.03 0.032 0.036 0.038
0.625 - 1.000 0.032 0.032 0.034 0.038 0.04

 

 

HSLA Thickness tolerances available
ASTM A568 (2015) / A635 (2007)
20 - 32 32 - 40 40 - 48 48 - 60 60 - 72 72 - 80 > 80
0.031 - 0.051 0.012 0.012 0.012 0.012 0.012 0.012 0.012
0.051 - 0.059 0.012 0.012 0.014 0.014 0.014 0.014 0.014
0.059 - 0.070 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.070 - 0.082 0.014 0.014 0.014 0.014 0.016 0.016 0.016
0.082 - 0.098 0.014 0.016 0.116 0.016 0.018 0.018 0.02
0.098 - 0.179 0.016 0.016 0.02 0.02 0.022 0.024 0.024
0.179 - 0.229 0.018 0.018 0.02 0.02 0.022 0.024 0.024
0.229 - 0.313 0.022 0.022 0.024 0.024 0.026 0.03 0.03
0.313 - 0.375 0.024 0.024 0.026 0.028 0.03 0.032 0.032
0.375 - 0.500 0.028 0.028 0.028 0.03 0.032 0.036 0.036
0.500 - 0.625 0.03 0.03 0.03 0.032 0.036 0.038 0.038
0.625 - 1.000 0.032 0.032 0.032 0.034 0.038 0.04 0.04

 

Option for maximum crown values

At the time of ordering, specific agreements can be made on the crown of hot-rolled strip.

 

Tolerances on width, edge camber and flatness

Material will be supplied conforming to the tolerances specified in ASTM A568 (2007) / A635 (2007). Width tolerances are over, no tolerance under.

Width tolerances available  
Carbon steel ASTM A568: 2015 / A635: 2015
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 0.937 0.125
30 - 35 1.125 0.187
35 - 48 1.125 0.187
48 - 50 1.125 0.25
50 - 60 1.5 0.25
60 - 65 1.5 0.312
65 - 70 1.5 0.312
70 - 78 1.5 0.312
78 - 80 1.875 0.312
80 - 82 1.875 0.375

 

Width tolerances available  
HSLA ASTM A568: 2015 / A635: 2007
Mill edge Cut edge
24 - 26 0.812 0.125
26 - 28 0.937 0.125
28 - 30 1.125 0.125
30 - 35 1.125 0.187
35 - 48 1.25 0.187
48 - 50 1.25 0.25
50 - 60 1.5 0.25
60 - 65 1.625 0.312
65 - 70 1.75 0.312
70 - 78 1.875 0.312
78 - 80 2 0.375
80 - 82 1.875 0.375

 

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights.

Description Capability
Coil diameter inner non-pickled 30 inch
Coil diameter inner pickled 24 inch standard
30 inch on request
Tolerance on inner diameter +0/-2 inch
Coil diameter outer non-pickled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 41.5 inch
Coil diameter outer pickled and oiled Outer diameter available is 10/7 x width to reduce possibility of coil tipping over
Max. 86 inch
Min. 65 inch
Coil weight Max. 75,000 lbs
Maximum coil weight limits can vary due to
transport limits and outer coil diameter
Some HR products may have different coil weight ranges
PIW  width ≤ 47 inch 868 - 1288 PIW width
PIW  47 inch < width ≤ 67 inch 868 - 1215 PIW width
PIW  width > 67 inch 616 PIW width and 868 - 1215 PIW width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply