High-strength steel
Ymagine® direct-rolled steel comes in five high-strength, low-alloy (HSLA) grades offering either weight savings or enhanced product strength without weight penalties.
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 45 XF TSN
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 45-Properties TSN
Properties
Relationship with standards and mechanical properties
The values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction.
| Tata Steel grade | Ymagine® 45 XF | |
|---|---|---|
| ASTM A 1011: 2007 | Hot-rolled flat products | HSLAS grade 45 class 2 |
| Yield strength | ksi | ≥ 45 |
| Tensile strength | ksi | ≥ 55 |
| Elongation | % | ≥ 23 |
| Tata Steel grade | Ymagine® 45 XF | |
|---|---|---|
| ASTM A 1008: 2013 | Cold-rolled flat products | HSLAS grade 45 class 2 |
| Yield strength | ksi | ≥ 45 |
| Tensile strength | ksi | ≥ 55 |
| Elongation (2 inch) | % | ≥ 22 |
| Tata Steel grade | Direct-rolled flat products | Ymagine® 45 XF | |
|---|---|---|---|
| Typical value | Guaranteed values | ||
| Yield strength | ksi | 50 | 45 - 65 |
| Tensile strength | ksi | 62 | 55 - 70 |
| Elongation | % | 30 | ≥ 25 |
Min. Elongation after fracture uses test piece length L0 is 2 inches.
Please contact us for further information on Charpy toughness and impact test properties.
Chemical composition
Heat analysis in weight percentages.
| Tata Steel grade | Ymagine® 45 XF | |
|---|---|---|
| Typical | Guaranteed (max) | |
| C | 0.045 | 0.065 |
| Mn | 0.250 | 0.375 |
| P | 0.008 | 0.020 |
| S | 0.007 | 0.015 |
| Si | 0.018 | 0.035 |
| Cb | 0.010 | 0.015 |
For the purpose of batch galvanizing, Ymagine® high-strength steels can be ordered on consultation with a maximum Si content of 0.030%..
EN_US-Engineering-Product-Direct-rolled-HSS-Ymagine 45-Dimensions TSN
Dimensions
Dimensional capability (pickled)
Dimensions in inches.
| Thickness | Maximum width |
|---|---|
| From - up to | Ymagine® 45 XF |
| 0.045 - 0.047 | 60 |
| 0.047 - 0.059 | 60 |
| 0.059 - 0.079 | 60 |
| 0.079 - 0.118 | 60 |
Minimum width is 39.37.
Other dimensions may be available - please contact us.
EN_US-Engineering-Product-Direct-rolled-All grades Shape and dimensional tolerancesTSN
Shape and dimensional tolerances
Tolerances on thickness
Ymagine® is available with the following tolerances. Thickness tolerances over, no tolerance under.
Dimensions in inches.
| Thickness | Tolerances |
|---|---|
| 0.045 ≤ t ≤ 0.078 | 0.004 |
| 0.078 < t ≤ 0.098 | 0.005 1 |
| 0.098 < t ≤ 0.118 | 0.006 2 |
1. In some instances, the material will be supplied with a total tolerance of 0.009 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
2. In some instances, the material will be supplied with a total tolerance of 0.010 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
Tolerances on width
Width tolerances comply with standard ASTM A568: 2011
Width tolerances over, no tolerance under.
Closer tolerances are possible – please contact us.
Dimensions and coil weights
The weight of weldless coils can be specified freely between 560 and 1148 PIW.
Ymagine is supplied with trimmed edges as standard. Mill edges are available on request.
| Description | Dimension or weight | |
|---|---|---|
| Outside diameter | minimum 41.4 inch | |
| maximum 78.74 inch (Ymagine®) | ||
| maximum 87.67 inch (mill scale) | ||
| Coil weight | maximum 69,500 lbs 1 | |
| PIW | minimum 560 PIW maximum 1148 PIW |
|
1. For Ymagine 70 XF the maximum coil weight is 55,000 lbs for thicknesses > 0.098 inch.
Tata Steel assumes a minimum and a maximum coil weight agreed upon with the customer on the basis of our normal production practices and an order quantity corresponding to this coil weight.
Usually a minimum coil weight up to 90% of the maximum coil weight can be requested.
Surface aspects
The surface quality of Ymagine is comparable to that of hot-rolled steel.
The roughness is comparable to hot-rolled pickled and oiled material i.e. 35 - 100 μinch CLA.
Ymagine is suitable for cold-rolled applications that are not surface-critical.
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 50 XF TSN
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 50-Properties TSN
Properties
Relationship with standards and mechanical properties
The values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction.
| Tata Steel grade | Ymagine 50 XF | |
|---|---|---|
| ASTM A 1011: 2007 | Hot-rolled flat products | HSLAS-F grade 50 |
| Yield strength | ksi | ≥ 50 |
| Tensile strength | ksi | ≥ 60 |
| Elongation | % | ≥ 22 |
| Tata Steel grade | Ymagine 50 XF | |
|---|---|---|
| ASTM A 1008: 2013 | Cold-rolled flat products | HSLAS-F grade 50 |
| Yield strength | ksi | ≥ 50 |
| Tensile strength | ksi | ≥ 60 |
| Elongation | % | ≥ 22 |
| Tata Steel grade | Direct-rolled flat products | Ymagine 50 XF | |
|---|---|---|---|
| Typical value | Guaranteed values | ||
| Yield strength | ksi | 55 | 50 - 70 |
| Tensile strength | ksi | 66 | 60 - 75 |
| Elongation (2 inch) | % | 29 | ≥ 22 |
Min. Elongation after fracture uses test piece length L0 is 2 inches.
Please contact us for further information on Charpy toughness and impact test properties.
Chemical composition
Heat analysis in weight percentages.
| Tata Steel grade | Ymagine 50 XF | |
|---|---|---|
| Typical | Guaranteed (max) | |
| C | 0.045 | 0.065 |
| Mn | 0.500 | 0.800 |
| P | 0.008 | 0.020 |
| S | 0.006 | 0.015 |
| Si | 0.018 | 0.035 |
| Cb | 0.013 | 0.020 |
For the purpose of batch galvanizing, Ymagine high-strength steels can be ordered on consultation with a maximum Si content of 0.030%..
EN_US-Engineering-Product-Direct-rolled-HSS-Ymagine 50-Dimensions TSN
Dimensions
Dimensional capability (pickled)
Dimensions in inches.
| Thickness | Maximum width |
|---|---|
| From - up to | Ymagine® 50 XF |
| 0.045 - 0.047 | - |
| 0.047 - 0.059 | 60 |
| 0.059 - 0.079 | 60 |
| 0.079 - 0.118 | 60 |
Minimum width is 39.37 inch.
Other dimensions may be available - please contact us.
Tolerances on thickness
Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2015.
Tighter tolerances are available, please contact us. Tolerances are over, no under.
EN_US-Engineering-Product-Direct-rolled-All grades Shape and dimensional tolerancesTSN
Shape and dimensional tolerances
Tolerances on thickness
Ymagine® is available with the following tolerances. Thickness tolerances over, no tolerance under.
Dimensions in inches.
| Thickness | Tolerances |
|---|---|
| 0.045 ≤ t ≤ 0.078 | 0.004 |
| 0.078 < t ≤ 0.098 | 0.005 1 |
| 0.098 < t ≤ 0.118 | 0.006 2 |
1. In some instances, the material will be supplied with a total tolerance of 0.009 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
2. In some instances, the material will be supplied with a total tolerance of 0.010 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
Tolerances on width
Width tolerances comply with standard ASTM A568: 2011
Width tolerances over, no tolerance under.
Closer tolerances are possible – please contact us.
Dimensions and coil weights
The weight of weldless coils can be specified freely between 560 and 1148 PIW.
Ymagine is supplied with trimmed edges as standard. Mill edges are available on request.
| Description | Dimension or weight | |
|---|---|---|
| Outside diameter | minimum 41.4 inch | |
| maximum 78.74 inch (Ymagine®) | ||
| maximum 87.67 inch (mill scale) | ||
| Coil weight | maximum 69,500 lbs 1 | |
| PIW | minimum 560 PIW maximum 1148 PIW |
|
1. For Ymagine 70 XF the maximum coil weight is 55,000 lbs for thicknesses > 0.098 inch.
Tata Steel assumes a minimum and a maximum coil weight agreed upon with the customer on the basis of our normal production practices and an order quantity corresponding to this coil weight.
Usually a minimum coil weight up to 90% of the maximum coil weight can be requested.
Surface aspects
The surface quality of Ymagine is comparable to that of hot-rolled steel.
The roughness is comparable to hot-rolled pickled and oiled material i.e. 35 - 100 μinch CLA.
Ymagine is suitable for cold-rolled applications that are not surface-critical.
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 60 XF TSN
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 60-Properties TSN
Properties
Relationship with standards and mechanical properties
The values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction.
| Tata Steel grade | Ymagine® 60 XF | |
|---|---|---|
| ASTM A 1011: 2007 | Hot-rolled flat products | HSLAS-F grade 60 |
| Yield strength | ksi | ≥ 60 |
| Tensile strength | ksi | ≥ 70 |
| Elongation | % | ≥ 20 |
| Tata Steel grade | Ymagine® 60 XF | |
|---|---|---|
| ASTM A 1008: 2013 | Cold-rolled flat products | HSLAS-F grade 60 |
| Yield strength | ksi | ≥ 60 |
| Tensile strength | ksi | ≥ 70 |
| Elongation (2 inch) | % | ≥ 18 |
| Tata Steel grade | Direct-rolled flat products | Ymagine® 60 XF | |
|---|---|---|---|
| Typical value | Guaranteed values | ||
| Yield strength | ksi | 67 | 60 - 80 |
| Tensile strength | ksi | 76 | 70 - 85 |
| Elongation (2 inch) | % | 26 | ≥ 20 |
Min. Elongation after fracture uses test piece length L0 is 2 inches.
Please contact us for further information on Charpy toughness and impact test properties.
Chemical composition
Heat analysis in weight percentages.
| Tata Steel grade | Ymagine® 60 XF | |
|---|---|---|
| Typical | Guaranteed (max) | |
| C | 0.045 | 0.075 |
| Mn | 0.800 | 1000 |
| P | 0.009 | 0.020 |
| S | 0.006 | 0.015 |
| Si | 0.020 | 0.035 |
| Cb | 0.015 | 0.020 |
| V | 0.040 | 0.060 |
For the purpose of batch galvanizing, Ymagine® high-strength steels can be ordered on consultation with a maximum Si content of 0.030%..
EN_US-Engineering-Product-Direct-rolled-HSS-Ymagine 60-Dimensions TSN
Dimensions
Dimensional capability (pickled)
Dimensions in inches.
| Thickness | Maximum width |
|---|---|
| From - up to | Ymagine® 60 XF |
| 0.045 - 0.047 | - |
| 0.047 - 0.059 | 53 |
| 0.059 - 0.079 | 60 |
| 0.079 - 0.118 | 60 |
Minimum width is 43.3 inch.
Other dimensions may be available - please contact us.
Tolerances on thickness
Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2015.
Tighter tolerances are available, please contact us. Tolerances are over, no under.
EN_US-Engineering-Product-Direct-rolled-All grades Shape and dimensional tolerancesTSN
Shape and dimensional tolerances
Tolerances on thickness
Ymagine® is available with the following tolerances. Thickness tolerances over, no tolerance under.
Dimensions in inches.
| Thickness | Tolerances |
|---|---|
| 0.045 ≤ t ≤ 0.078 | 0.004 |
| 0.078 < t ≤ 0.098 | 0.005 1 |
| 0.098 < t ≤ 0.118 | 0.006 2 |
1. In some instances, the material will be supplied with a total tolerance of 0.009 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
2. In some instances, the material will be supplied with a total tolerance of 0.010 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
Tolerances on width
Width tolerances comply with standard ASTM A568: 2011
Width tolerances over, no tolerance under.
Closer tolerances are possible – please contact us.
Dimensions and coil weights
The weight of weldless coils can be specified freely between 560 and 1148 PIW.
Ymagine is supplied with trimmed edges as standard. Mill edges are available on request.
| Description | Dimension or weight | |
|---|---|---|
| Outside diameter | minimum 41.4 inch | |
| maximum 78.74 inch (Ymagine®) | ||
| maximum 87.67 inch (mill scale) | ||
| Coil weight | maximum 69,500 lbs 1 | |
| PIW | minimum 560 PIW maximum 1148 PIW |
|
1. For Ymagine 70 XF the maximum coil weight is 55,000 lbs for thicknesses > 0.098 inch.
Tata Steel assumes a minimum and a maximum coil weight agreed upon with the customer on the basis of our normal production practices and an order quantity corresponding to this coil weight.
Usually a minimum coil weight up to 90% of the maximum coil weight can be requested.
Surface aspects
The surface quality of Ymagine is comparable to that of hot-rolled steel.
The roughness is comparable to hot-rolled pickled and oiled material i.e. 35 - 100 μinch CLA.
Ymagine is suitable for cold-rolled applications that are not surface-critical.
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 70 XF TSN
EN_US-Engineering-Product-Direct-Rolled-HSS-Ymagine 70-Properties TSN
Properties
Relationship with standards and mechanical properties
The values shown for the mechanical properties in the table below are for test pieces taken longitudinal to the rolling direction.
| Tata Steel grade | Ymagine® 70 XF | ||
|---|---|---|---|
| ASTM A 1011: 2007 | Hot-rolled flat products | HSLAS-F grade 70 | |
| Yield strength | ksi | ≥ 70 | |
| Tensile strength | ksi | ≥ 80 | |
| Elongation | % | ≥ 18 | |
| Tata Steel grade | Ymagine® 70 XF | |
|---|---|---|
| ASTM A 1008: 2013 | Cold-rolled flat products | HSLAS-F grade 70 |
| Yield strength | ksi | ≥ 70 |
| Tensile strength | ksi | ≥ 80 |
| Elongation (2 inch) | % | ≥ 16 |
| Tata Steel grade | Direct-rolled flat products | Ymagine® 70 XF | |
|---|---|---|---|
| Typical value | Guaranteed values | ||
| Yield strength | ksi | 78 | 70 - 95 |
| Tensile strength | ksi | 90 | 80 - 105 |
| Elongation (2 inch) | % | 22 | ≥ 16 |
Min. Elongation after fracture uses test piece length L0 is 2 inches.
Please contact us for further information on Charpy toughness and impact test properties.
Chemical composition
Heat analysis in weight percentages.
| Tata Steel grade | Ymagine® 70 XF | |
|---|---|---|
| Typical | Guaranteed (max) | |
| C | 0.045 | 0.075 |
| Mn | 0.800 | 1000 |
| P | 0.009 | 0.020 |
| S | 0.006 | 0.010 |
| Si | 0.020 | 0.035 |
| Cb | 0.015 | 0.020 |
| V | 0.130 | 0.150 |
For the purpose of batch galvanizing, Ymagine® high-strength steels can be ordered on consultation with a maximum Si content of 0.030%..
EN_US-Engineering-Product-Direct-rolled-HSS-Ymagine 70-Dimensions TSN
Dimensions
Dimensional capability (pickled)
Dimensions in inches.
| Thickness | Maximum width |
|---|---|
| From - up to | Ymagine® 70 XF |
| 0.047 - 0.059 | - |
| 0.059 - 0.079 | 53 |
| 0.079 - 0.118 | 57 |
Minimum width is 45.3 inch.
Other dimensions may be available - please contact us.
Tolerances on thickness
Tolerances for wide strip and slit wide strip comply with standard ASTM A568: 2007 and A635: 2015.
Tighter tolerances are available, please contact us. Tolerances are over, no under.
EN_US-Engineering-Product-Direct-rolled-All grades Shape and dimensional tolerancesTSN
Shape and dimensional tolerances
Tolerances on thickness
Ymagine® is available with the following tolerances. Thickness tolerances over, no tolerance under.
Dimensions in inches.
| Thickness | Tolerances |
|---|---|
| 0.045 ≤ t ≤ 0.078 | 0.004 |
| 0.078 < t ≤ 0.098 | 0.005 1 |
| 0.098 < t ≤ 0.118 | 0.006 2 |
1. In some instances, the material will be supplied with a total tolerance of 0.009 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
2. In some instances, the material will be supplied with a total tolerance of 0.010 inch, only on the coil head and tail and to a maximum of 66 ft. from the start of the coil.
Tolerances on width
Width tolerances comply with standard ASTM A568: 2011
Width tolerances over, no tolerance under.
Closer tolerances are possible – please contact us.
Dimensions and coil weights
The weight of weldless coils can be specified freely between 560 and 1148 PIW.
Ymagine is supplied with trimmed edges as standard. Mill edges are available on request.
| Description | Dimension or weight | |
|---|---|---|
| Outside diameter | minimum 41.4 inch | |
| maximum 78.74 inch (Ymagine®) | ||
| maximum 87.67 inch (mill scale) | ||
| Coil weight | maximum 69,500 lbs 1 | |
| PIW | minimum 560 PIW maximum 1148 PIW |
|
1. For Ymagine 70 XF the maximum coil weight is 55,000 lbs for thicknesses > 0.098 inch.
Tata Steel assumes a minimum and a maximum coil weight agreed upon with the customer on the basis of our normal production practices and an order quantity corresponding to this coil weight.
Usually a minimum coil weight up to 90% of the maximum coil weight can be requested.
Surface aspects
The surface quality of Ymagine is comparable to that of hot-rolled steel.
The roughness is comparable to hot-rolled pickled and oiled material i.e. 35 - 100 μinch CLA.
Ymagine is suitable for cold-rolled applications that are not surface-critical.
EN_US-Engineering-Product-Cold-rolled-HSS TSE
Tata Steel offers a range of cold-rolled steels for applications requiring high strength without the weight penalty
The range comprises micro-alloyed, rephosphorised and carbon manganese
EN_US-Engineering-Product-Hot-Rolled-HSS TSE
Tata Steel’s hot-rolled high-strength, low-alloy (HSLA) grades offer formability and strength for demanding applications
The range includes Ympress® with grade
EN_US-Automotive-Contact-General sales - Automotive - general
Automotive sales enquiries and customer services
Please contact us for further information, questions and enquiries. Working together on sustainable vehicles and value chains.