Hot-rolled

Structural steel

The guaranteed strength and good weldability of our hot-rolled structural steel help ensure ease of processing and reliable end-product performance.

As with all our hot-rolled steel products, our structural steel is manufactured under tight controls – for consistent quality that you can depend on.

Applications

  • Automotive wheel rims and chassis components
  • Construction and building
  • Cold formed sections
  • Pressure vessels
  • Transport
  • Tubes and pipes
  • Warehouse shelving
  • Heavy vehicles equipment
Abrasion resistant wear steel
Cold-formed C section made with hot-rolled steel
Product specification
Structural steel is currently available in the following grades

EN-Engineering-Product-Hot-Rolled-Structural steel-S185+AR TSE

S185+AR
Specification details for S185+AR

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades OverviewTSE

Overview

Availability

Structural steel products are available as follows:

  • As-rolled (+AR)

  • Normalised rolling (+N)

  • Suitable for cold forming (C)

  • Suitable for post-galvanising (Class 1)

  • Weathering steel (W)

Relationship with standards

Hot-rolled structural steel complies with European standard EN 10025: 2004 and is available in the grades shown in the table below.

If normalised rolling (+N) or cold forming (C) is required, please specify when ordering. In these cases, this should be indicated by adding the relevant letter to the grade at the time of ordering (for example: S355J0C+AR). Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

European standard Charpy Weathering steel European standard As Rolled Normalised Suitable for Cold forming Suitable for Post galvanising
EN 10025-2: 2004 JR J0 J2 K2 W EN 10025-2: 2006 AR +N C Class I
S185             Y   Y Y
S235 Y Y Y       Y Y Y Y
S275 Y Y Y       Y Y Y Y
S355 Y Y Y Y Y   Y Y Y Y
 

The CE mark

The CE mark is a symbol devised by the European Council to signify that a product meets the conditions of the applicable council directives. These conditions aim to ensure that the product is reliable and safe. Products that are “produced for incorporation in a permanent manner in construction works” fall under the Construction Products Directive. Hot-rolled steels covered by EN 10025: 2004 are used in such “works” and are therefore covered by the directive. For these products, Tata Steel’s test certificates bear the CE mark and Tata Steel has issued a certified Declaration of Performance (DoP). All the structural products produced by Tata Steel in Europe are CE-marked except for S185+AR.
 

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition

non-pickled

pickled

pickled and oiled

Mill edges

Yes

Yes

Yes

Trimmed edges

-

Yes

Yes

Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.

Surface aspects

Description

Availability

Surface finish

Coils are available in non-pickled and pickled finish

Oiling

Pickled finish is available with rolling or preservative oil applied

 

Oil weight normally 0.5-2.5 g/m2

Alternative oiling ranges are available – please contact us for details.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE

Supply Conditions

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
Trimmed edges available in thicknesses up to 8.0 mm.
Please contact us regarding other specifications we may have that meet your needs.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling
or preservative oil applied. 
Oil weight normally 0.5-2.5 g/m2
Alternative oiling ranges are available.
Please contact us for details.
 

Certification

Test certificates 2.2/3.1 are available according to EN 10204.         

EN-Engineering-Product-Hot-Rolled-Structural Steel-S185-Properties TSE

Properties

Mechanical Properties

The values shown for strength and elongation in the table below are for test pieces taken transverse to the rolling direction; those for the impact test are for test pieces taken in the rolling direction.

EN 10025-2: 2004   Grade S185
Min. yield strength 1, 2 ReH1 2 (N/mm2) t ≤ 16 185
16 < t ≤ 20 175
Tensile strength Rm (N/mm2) t < 3 310 - 540
3 ≤ t ≤ 20 290 - 510
Elongation % 1.5 < t ≤ 2 10
2 < t ≤ 2.5 11
2.5 < t < 3 12
    3 ≤ t ≤ 20 16
Impact stength Temp. °C   -
Min. energy J   -
1. Upper yield strength or 0.2% proof stress applies.
2. For thicknesses > 16 mm, the ReH value is decreased by 10 N/mm2.
3. The impact properties of quality JR products are verified only when specified at the time of enquiry or order.
   Impact strengths apply to thicknesses > 6 mm and are for standard test pieces only. Please contact us for details.
   For the mechanical properties of cold-forming qualities, please consult us.
Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 mm. L0 = 5.65√S0 for t ≥ 3 mm.
t – material thickness in mm.

Chemical composition

Structural steel meets the requirements of the cast analysis in the standard, as shown in the table below.

The steel grades supplied by Tata Steel are always fully killed.
Tata Steel does not supply steel with increased copper content.

Grade   S185
C Max.
Mn Max.
P Max.
S Max.
Si Max.
N Max.
Cu Max. 0.55
The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020% or if sufficient other nitrogen-binding elements are present.
The nitrogen-binding elements shall be mentioned in the inspection document.
For the chemical composition of cold-forming qualities, please consult us.
The chemical composition of steels suitable for galvanising complies with EN 10025-2: 2004.
All values are in weight%.
 

Suitability for cold forming

If chemistry suitable for cold forming (+C) is required, this must be specified when the material is ordered.
Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.
 

Suitability for galvanising

If chemistry suitable for post-galvanising (Class 1) is required, this must be specified when the material is ordered.

EN-Engineering-Product-Hot-Rolled-Structural Steel-S185-Dimensions TSE

Dimensions

Dimensional capability - non-pickled

Dimensions in mm.

Thickness Max. width
From - up to S185
1.47 - 1.49 1300
1.49 - 1.50 1320
1.50 - 1.53 1330
1.53 - 1.57 1350
1.57 - 1.60 1380
1.60 - 1.70 1410
1.70 - 1.80 1480
1.80 - 2.00 1550
2.00 - 2.20 1700
2.20 - 2.40 1820
2.40 - 2.60 1920
2.60 - 2.70 2030
2.70 - 20.00 2070
All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm except for thicknesses above 20 mm where the minimum width is 1500 mm.
Other dimensions are available - please contact us.
 

Dimensional capability - pickled

Dimensions in mm.

Thickness Max. width
From - up to S185
1.50 - 1.53 1330
1.53 - 1.57 1350
1.57 - 1.60 1380
1.60 - 1.70 1410
1.70 - 1.80 1480
1.80 - 2.00 1550
2.00 - 2.20 1700
2.20 - 2.40 1820
2.40 - 2.60 1920
2.60 - 2.70 2030
2.70 - 12.25 2070
12.25 - 15.00 1600
All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm. Widths smaller than 900 mm are available - please contact us.
Thicknesses up to 20 mm may be available - please contact us.
 

Tolerances

Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.

Tighter tolerances are available, please contact us.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE

Shape and dimensional tolerances

Shape and dimensional tolerances

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:

length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

 

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.

Tighter tolerances are available as shown below:

Product type Thickness tolerances available
  (% of full EN 10051:2010 tolerance)
  100% 75% 66% 60% 50% 33%

Steel for forming

Yes

Yes

Yes

Yes

Yes

Yes 1

High-strength low-alloy
(HSLA EN 10149-2)

Yes

Yes

Yes

Yes

Yes

Yes 1

Ympress® HSLA

 

 

 

 

Yes

Yes 1

Ympress® Laser

 

 

 

 

Yes

Yes 1

Structural steel

Yes

Yes

Yes

Yes

Yes

Yes 1

Boron manganese steel Yes Yes Yes Yes Yes  

Case-hardening steel

Yes

Yes

Yes

Yes

Yes

 

High-carbon steel

Yes

 

 

 

 

 

Dual phase steel

Yes

 

 

 

 

 

Hot forming steel

Yes

 

 

 

 

 

Valast® abrasion resistant steel

Yes

Yes

Yes

Yes

Yes

 

Steel for pressure vessels

Yes

 

 

 

 

 

Steel for gas cylinders

Yes

 

 

 

 

 

Steel for line pipe

Yes

 

 

 

 

 

Ship plate

Yes

 

 

 

 

 

1. Available for certain grades and thicknesses between 3.0mm and 6.0mm.
Please contact us on the availability of special tolerances to meet your requirements.
 
Tolerances on thickness for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.13

± 0.14

± 0.16

-

> 2.00

≤ 2.50

± 0.14

± 0.16

± 0.17

± 0.19

> 2.50

≤ 3.00

± 0.15

± 0.17

± 0.18

± 0.20

> 3.00

≤ 4.00

± 0.17

± 0.18

± 0.20

± 0.20

> 4.00

≤ 5.00

± 0.18

± 0.20

± 0.21

± 0.22

> 5.00

≤ 6.00

± 0.20

± 0.21

± 0.22

± 0.23

> 6.00

≤ 8.00

± 0.22

± 0.23

± 0.23

± 0.26

> 8.00

≤ 11.00

± 0.24

± 0.25

± 0.25

± 0.28

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
Re ≤ 300 N/mm2 (category A)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800
 

≤ 2.00

± 0.17

± 0.19

± 0.21

-

> 2.00

≤ 2.50

± 0.18

± 0.21

± 0.23

± 0.25

> 2.50

≤ 3.00

± 0.20

± 0.22

± 0.24

± 0.26

> 3.00

≤ 4.00

± 0.22

± 0.24

± 0.26

± 0.27

> 4.00

≤ 5.00

± 0.24

± 0.26

± 0.28

± 0.29

> 5.00

≤ 6.00

± 0.26

± 0.28

± 0.29

± 0.31

> 6.00

≤ 8.00

± 0.29

± 0.30

± 0.31

± 0.35

> 8.00

≤ 10.00

± 0.32

± 0.33

± 0.34

± 0.40

> 10.00

≤ 12.50

± 0.35

± 0.36

± 0.37

± 0.43

> 12.50

≤ 15.00

± 0.37

± 0.38

± 0.40

± 0.46

> 15.00

≤ 25.00

± 0.40

± 0.42

± 0.45

± 0.50

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
300 N/mm2 < Re ≤ 360 N/mm2 (category B)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.20

± 0.22

± 0.24

-

> 2.00

≤ 2.50

± 0.21

± 0.24

± 0.26

± 0.29

> 2.50

≤ 3.00

± 0.23

± 0.25

± 0.28

± 0.30

> 3.00

≤ 4.00

± 0.25

± 0.28

± 0.30

± 0.31

> 4.00

≤ 5.00

± 0.28

± 0.30

± 0.32

± 0.33

> 5.00

≤ 6.00

± 0.30

± 0.32

± 0.33

± 0.36

> 6.00

≤ 8.00

± 0.33

± 0.35

± 0.36

± 0.40

> 8.00

≤ 10.00

± 0.37

± 0.38

± 0.39

± 0.46

> 10.00

≤ 12.50

± 0.40

± 0.41

± 0.43

± 0.49

> 12.50

≤ 15.00

± 0.43

± 0.44

± 0.46

± 0.53

> 15.00

≤ 25.00

± 0.46

± 0.48

± 0.52

± 0.58

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
360 N/mm2 < Re ≤ 420 N/mm2 (category C)
Nominal thickness

Tolerances for a nominal width of

≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.22

± 0.25

± 0.27

-

> 2.00

≤ 2.50

± 0.23

± 0.27

± 0.30

± 0.33

> 2.50

≤ 3.00

± 0.26

± 0.29

± 0.31

± 0.34

> 3.00

≤ 4.00

± 0.29

± 0.31

± 0.34

± 0.35

> 4.00

≤ 5.00

± 0.31

± 0.34

± 0.36

± 0.38

> 5.00

≤ 6.00

± 0.34

± 0.36

± 0.38

± 0.40

> 6.00

≤ 8.00

± 0.38

± 0.39

± 0.40

± 0.46

> 8.00

≤ 10.00

± 0.42

± 0.43

± 0.44

± 0.52

> 10.00

≤ 12.50

± 0.46

± 0.47

± 0.48

± 0.56

> 12.50

≤ 15.00

± 0.48

± 0.49

± 0.52

± 0.60

> 15.00

≤ 25.00

± 0.52

± 0.55

± 0.59

± 0.65

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
420 N/mm2 < Re ≤ 900 N/mm2 (category D)

Nominal thickness

Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.24

± 0.27

± 0.29

-

> 2.00

≤ 2.50

± 0.25

± 0.29

± 0.32

± 0.35

> 2.50

≤ 3.00

± 0.28

± 0.31

± 0.34

± 0.36

> 3.00

≤ 4.00

± 0.31

± 0.34

± 0.36

± 0.38

> 4.00

≤ 5.00

± 0.34

± 0.36

± 0.39

± 0.41

> 5.00

≤ 6.00

± 0.36

± 0.39

± 0.41

± 0.43

> 6.00

≤ 8.00

± 0.41

± 0.42

± 0.43

± 0.49

> 8.00

≤ 10.00

± 0.45

± 0.46

± 0.48

± 0.56

> 10.00

≤ 12.50

± 0.49

± 0.50

± 0.52

± 0.60

> 12.50

≤ 15.00

± 0.52

± 0.53

± 0.56

± 0.64

> 15.00

≤ 25.00

± 0.56

± 0.59

± 0.63

± 0.70

All dimensions are mm.

Tolerances on width

Tolerances in mm.

Nominal width w
Mill edges Trimmed edges
lower upper lower upper

 w ≤ 1200

0

20

0

3

 1200 < w ≤ 1850

0

20

0

5

 w > 1850

0

25

0

6

Tolerances  in mm for wide strip and slit wide strip
The tolerances for wide strip and slit wide strip comply with standard EN 10051:2010.

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

Edge camber

The deviation from the edge over a length of 5000mm:

• with mill edges, no more than 20mm
• with trimmed edges, no more than 15mm

Flatness

Requirements as regards flatness can be agreed at the time of enquiry.

Option for maximum crown values

The following high crown C40 options available for hot-rolled products.

Crown values on the C20-position as well as minimum crown values on both C20 and C40 position are also available on request.

 

Maximum Crown C40 in µm values for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)

Category 1

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 3.00

40

40

50

50

> 3.00

≤ 6.00

40

50

50

50

> 6.00

≤ 11.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades
(S185-S235-S275 ≤ 10mm in EN 10025-2:2004)

Category 2

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 20.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades(S275 > 10mm in EN 10025-2:2004)
 and HSLA grades (S315MC in EN 10149-2:1996)

Category 3

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

50

50

60

60

> 2.00

≤ 2.50

50

60

60

60

> 2.50

≤ 3.00

50

60

60

60

> 3.00

≤ 20.00

60

60

70

70

 

Maximum Crown C40 in µm values of HSLA grades
 (S355MC, S420MC, S460MC, S500MC, S550MC in EN 10149-2:1996)

Category 4

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

60

70

70

70

> 2.00

≤ 2.50

60

70

80

80

> 2.50

≤ 3.00

60

70

80

80

> 3.00

≤ 5.00

70

70

80

80

> 5.00

≤ 20.00

80

80

80

80

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights:

Description

Availability

Coil diameter inner non-pickled

762mm

Coil diameter inner pickled

610mm standard

762mm on request

Tolerance on inner diameter

+0/-50mm

Coil diameter outer non-pickled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Max. 2200mm

Min. 1050mm

Coil diameter outer pickled and oiled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Outer diameter

limit 2200mm

Min. 1050mm

Coil weight

Max. 34 tonnes

Additional maximum limits from transport

limits and outer coil diameter

Some HR products may have different

coil weight ranges

KIM: width ≤ 1200mm

15.5 - 23.0 kg/mm width

KIM: 1200 < width ≤ 1700mm

12.1 - 21.7 kg/mm width

KIM: width > 1700mm

11.0 kg/mm width and 12.1 - 21.7 kg/mm width

Minimum tonnage per order

Please refer to price list for order quantity details

Minimum order quantities may apply

 

 

 

 

EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.

Heavy gauge processing

Processing type Decoiling
Thickness range (mm) 1.4 - 25.4
Width range (mm) 300 - 2600
Length range up to 18.4m
Locations UK
Netherlands

 

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands


For further information please visit our Service Centre webpages.

 

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades DownloadsTSE

Download

Download:

 

EN-Engineering-Product-Hot-Rolled-Structural steel-S235JR/J0/J2 TSE

S235JR/J0/J2
Specification details for S235JR/J0/J2

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades OverviewTSE

Overview

Availability

Structural steel products are available as follows:

  • As-rolled (+AR)

  • Normalised rolling (+N)

  • Suitable for cold forming (C)

  • Suitable for post-galvanising (Class 1)

  • Weathering steel (W)

Relationship with standards

Hot-rolled structural steel complies with European standard EN 10025: 2004 and is available in the grades shown in the table below.

If normalised rolling (+N) or cold forming (C) is required, please specify when ordering. In these cases, this should be indicated by adding the relevant letter to the grade at the time of ordering (for example: S355J0C+AR). Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

European standard Charpy Weathering steel European standard As Rolled Normalised Suitable for Cold forming Suitable for Post galvanising
EN 10025-2: 2004 JR J0 J2 K2 W EN 10025-2: 2006 AR +N C Class I
S185             Y   Y Y
S235 Y Y Y       Y Y Y Y
S275 Y Y Y       Y Y Y Y
S355 Y Y Y Y Y   Y Y Y Y
 

The CE mark

The CE mark is a symbol devised by the European Council to signify that a product meets the conditions of the applicable council directives. These conditions aim to ensure that the product is reliable and safe. Products that are “produced for incorporation in a permanent manner in construction works” fall under the Construction Products Directive. Hot-rolled steels covered by EN 10025: 2004 are used in such “works” and are therefore covered by the directive. For these products, Tata Steel’s test certificates bear the CE mark and Tata Steel has issued a certified Declaration of Performance (DoP). All the structural products produced by Tata Steel in Europe are CE-marked except for S185+AR.
 

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition

non-pickled

pickled

pickled and oiled

Mill edges

Yes

Yes

Yes

Trimmed edges

-

Yes

Yes

Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.

Surface aspects

Description

Availability

Surface finish

Coils are available in non-pickled and pickled finish

Oiling

Pickled finish is available with rolling or preservative oil applied

 

Oil weight normally 0.5-2.5 g/m2

Alternative oiling ranges are available – please contact us for details.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE

Supply Conditions

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
Trimmed edges available in thicknesses up to 8.0 mm.
Please contact us regarding other specifications we may have that meet your needs.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling
or preservative oil applied. 
Oil weight normally 0.5-2.5 g/m2
Alternative oiling ranges are available.
Please contact us for details.
 

Certification

Test certificates 2.2/3.1 are available according to EN 10204.         

EN-Engineering-Product-Hot-Rolled-Structural Steel-S235JR/J0/J2-Properties TSE

Properties

Mechanical Properties

The values shown for strength and elongation in the table below are for test pieces taken transverse to the rolling direction; those for the impact test are for test pieces taken in the rolling direction.

EN 10025-2: 2004   Grade S235JR/J0/J2
Min. yield strength 1, 2 ReH (N/mm2) t ≤ 16 235
16 < t ≤ 22 225
Tensile strength Rm (N/mm2) t < 3 360 - 510
3 ≤ t ≤ 20 360 - 510
Elongation % 1.5 < t ≤ 2 17
2 < t ≤ 2.5 18
2.5 < t < 3 19
3 ≤ t ≤ 20 24
Impact strength     JR 3 / J0 / J2
Temp. °C   20 / 0 / -20
Min. energy J   27
Chemical composition1. Upper yield strength or 0.2% proof stress applies.
2. For thicknesses > 16 mm, the ReH value is decreased by 10 N/mm2.
3. The impact properties of quality JR products are verified only when specified at the time of enquiry or order.
Impact strengths apply to thicknesses > 6 mm and are for standard test pieces only. Please contact us for details.
For the mechanical properties of cold-forming qualities, please consult us.
Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 mm. L0 = 5.65√S0 for t ≥ 3 mm.
t – material thickness in mm.

Impact strength

Impact tests can be performed for thicknesses ≥ 6.0 mm. Please contact us for details.

Chemical composition

Structural steel meets the requirements of the cast analysis in the standard, as shown in the table below.

The steel grades supplied by Tata Steel are always fully killed.
Tata Steel does not supply steel with increased copper content.

  Grade S235JR
C Max. 0.17
Mn Max. 1.40
P Max. 0.035
S Max. 0.035
Si Max.
N Max. 0.012
Cu Max. 0.55
The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020% or if sufficient other nitrogen-binding elements are present.
The nitrogen-binding elements shall be mentioned in the inspection document.
For the chemical composition of cold-forming qualities, please consult us.
The chemical composition of steels suitable for galvanising complies with EN 10025-2: 2004.
All values are in weight%.
 

Suitability for cold forming

If chemistry suitable for cold forming (+C) is required, this must be specified when the material is ordered.
Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.
 

Suitability for galvanising

If chemistry suitable for post-galvanising (Class 1) is required, this must be specified when the material is ordered.

EN-Engineering-Product-Hot-Rolled-Structural Steel-S235-Dimensions TSE

Dimensions

Dimensional capability - non-pickled

Dimensions in mm.

Thickness Max. width
From - up to S235JR/J0/J2
1.47 - 1.49 1300
1.49 - 1.50 1320
1.50 - 1.53 1330
1.53 - 1.57 1350
1.57 - 1.60 1380
1.60 - 1.70 1410
1.70 - 1.80 1480
1.80 - 2.00 1550
2.00 - 2.20 1700
2.20 - 2.40 1820
2.40 - 2.60 1920
2.60 - 2.70 2030
2.70 - 20.00 2070 1
All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm.

1. S235J2 available for thicknesses ≤ 12.70 mm. 
Other dimensions are available - please contact us.
 

Dimensional capability - pickled

Dimensions in mm.

Thickness Max. width
From - up to S235JR/J0/J2
1.50 - 1.53 1330
1.53 - 1.57 1350
1.57 - 1.60 1380
1.60 - 1.70 1410
1.70 - 1.80 1480
1.80 - 2.00 1550
2.00 - 2.20 1700
2.20 - 2.40 1820
2.40 - 2.60 1920
2.60 - 2.70 2030
2.70 - 12.25 2070
12.25 - 15.25 1600 1
All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm. Widths smaller than 900 mm are available - please contact us.
1. S235 J2 available for thicknesses ≤ 12.70 mm. 
Thicknesses up to 20 mm may be available - please contact us.
 

Tolerances

Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.

Tighter tolerances are available, please contact us.

EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE

Shape and dimensional tolerances

Shape and dimensional tolerances

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:

length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

 

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.

Tighter tolerances are available as shown below:

Product type Thickness tolerances available
  (% of full EN 10051:2010 tolerance)
  100% 75% 66% 60% 50% 33%

Steel for forming

Yes

Yes

Yes

Yes

Yes

Yes 1

High-strength low-alloy
(HSLA EN 10149-2)

Yes

Yes

Yes

Yes

Yes

Yes 1

Ympress® HSLA

 

 

 

 

Yes

Yes 1

Ympress® Laser

 

 

 

 

Yes

Yes 1

Structural steel

Yes

Yes

Yes

Yes

Yes

Yes 1

Boron manganese steel Yes Yes Yes Yes Yes  

Case-hardening steel

Yes

Yes

Yes

Yes

Yes

 

High-carbon steel

Yes

 

 

 

 

 

Dual phase steel

Yes

 

 

 

 

 

Hot forming steel

Yes

 

 

 

 

 

Valast® abrasion resistant steel

Yes

Yes

Yes

Yes

Yes

 

Steel for pressure vessels

Yes

 

 

 

 

 

Steel for gas cylinders

Yes

 

 

 

 

 

Steel for line pipe

Yes

 

 

 

 

 

Ship plate

Yes

 

 

 

 

 

1. Available for certain grades and thicknesses between 3.0mm and 6.0mm.
Please contact us on the availability of special tolerances to meet your requirements.
 
Tolerances on thickness for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.13

± 0.14

± 0.16

-

> 2.00

≤ 2.50

± 0.14

± 0.16

± 0.17

± 0.19

> 2.50

≤ 3.00

± 0.15

± 0.17

± 0.18

± 0.20

> 3.00

≤ 4.00

± 0.17

± 0.18

± 0.20

± 0.20

> 4.00

≤ 5.00

± 0.18

± 0.20

± 0.21

± 0.22

> 5.00

≤ 6.00

± 0.20

± 0.21

± 0.22

± 0.23

> 6.00

≤ 8.00

± 0.22

± 0.23

± 0.23

± 0.26

> 8.00

≤ 11.00

± 0.24

± 0.25

± 0.25

± 0.28

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
Re ≤ 300 N/mm2 (category A)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800
 

≤ 2.00

± 0.17

± 0.19

± 0.21

-

> 2.00

≤ 2.50

± 0.18

± 0.21

± 0.23

± 0.25

> 2.50

≤ 3.00

± 0.20

± 0.22

± 0.24

± 0.26

> 3.00

≤ 4.00

± 0.22

± 0.24

± 0.26

± 0.27

> 4.00

≤ 5.00

± 0.24

± 0.26

± 0.28

± 0.29

> 5.00

≤ 6.00

± 0.26

± 0.28

± 0.29

± 0.31

> 6.00

≤ 8.00

± 0.29

± 0.30

± 0.31

± 0.35

> 8.00

≤ 10.00

± 0.32

± 0.33

± 0.34

± 0.40

> 10.00

≤ 12.50

± 0.35

± 0.36

± 0.37

± 0.43

> 12.50

≤ 15.00

± 0.37

± 0.38

± 0.40

± 0.46

> 15.00

≤ 25.00

± 0.40

± 0.42

± 0.45

± 0.50

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
300 N/mm2 < Re ≤ 360 N/mm2 (category B)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.20

± 0.22

± 0.24

-

> 2.00

≤ 2.50

± 0.21

± 0.24

± 0.26

± 0.29

> 2.50

≤ 3.00

± 0.23

± 0.25

± 0.28

± 0.30

> 3.00

≤ 4.00

± 0.25

± 0.28

± 0.30

± 0.31

> 4.00

≤ 5.00

± 0.28

± 0.30

± 0.32

± 0.33

> 5.00

≤ 6.00

± 0.30

± 0.32

± 0.33

± 0.36

> 6.00

≤ 8.00

± 0.33

± 0.35

± 0.36

± 0.40

> 8.00

≤ 10.00

± 0.37

± 0.38

± 0.39

± 0.46

> 10.00

≤ 12.50

± 0.40

± 0.41

± 0.43

± 0.49

> 12.50

≤ 15.00

± 0.43

± 0.44

± 0.46

± 0.53

> 15.00

≤ 25.00

± 0.46

± 0.48

± 0.52

± 0.58

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
360 N/mm2 < Re ≤ 420 N/mm2 (category C)
Nominal thickness

Tolerances for a nominal width of

≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.22

± 0.25

± 0.27

-

> 2.00

≤ 2.50

± 0.23

± 0.27

± 0.30

± 0.33

> 2.50

≤ 3.00

± 0.26

± 0.29

± 0.31

± 0.34

> 3.00

≤ 4.00

± 0.29

± 0.31

± 0.34

± 0.35

> 4.00

≤ 5.00

± 0.31

± 0.34

± 0.36

± 0.38

> 5.00

≤ 6.00

± 0.34

± 0.36

± 0.38

± 0.40

> 6.00

≤ 8.00

± 0.38

± 0.39

± 0.40

± 0.46

> 8.00

≤ 10.00

± 0.42

± 0.43

± 0.44

± 0.52

> 10.00

≤ 12.50

± 0.46

± 0.47

± 0.48

± 0.56

> 12.50

≤ 15.00

± 0.48

± 0.49

± 0.52

± 0.60

> 15.00

≤ 25.00

± 0.52

± 0.55

± 0.59

± 0.65

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
420 N/mm2 < Re ≤ 900 N/mm2 (category D)

Nominal thickness

Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.24

± 0.27

± 0.29

-

> 2.00

≤ 2.50

± 0.25

± 0.29

± 0.32

± 0.35

> 2.50

≤ 3.00

± 0.28

± 0.31

± 0.34

± 0.36

> 3.00

≤ 4.00

± 0.31

± 0.34

± 0.36

± 0.38

> 4.00

≤ 5.00

± 0.34

± 0.36

± 0.39

± 0.41

> 5.00

≤ 6.00

± 0.36

± 0.39

± 0.41

± 0.43

> 6.00

≤ 8.00

± 0.41

± 0.42

± 0.43

± 0.49

> 8.00

≤ 10.00

± 0.45

± 0.46

± 0.48

± 0.56

> 10.00

≤ 12.50

± 0.49

± 0.50

± 0.52

± 0.60

> 12.50

≤ 15.00

± 0.52

± 0.53

± 0.56

± 0.64

> 15.00

≤ 25.00

± 0.56

± 0.59

± 0.63

± 0.70

All dimensions are mm.

Tolerances on width

Tolerances in mm.

Nominal width w
Mill edges Trimmed edges
lower upper lower upper

 w ≤ 1200

0

20

0

3

 1200 < w ≤ 1850

0

20

0

5

 w > 1850

0

25

0

6

Tolerances  in mm for wide strip and slit wide strip
The tolerances for wide strip and slit wide strip comply with standard EN 10051:2010.

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

Edge camber

The deviation from the edge over a length of 5000mm:

• with mill edges, no more than 20mm
• with trimmed edges, no more than 15mm

Flatness

Requirements as regards flatness can be agreed at the time of enquiry.

Option for maximum crown values

The following high crown C40 options available for hot-rolled products.

Crown values on the C20-position as well as minimum crown values on both C20 and C40 position are also available on request.

 

Maximum Crown C40 in µm values for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)

Category 1

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 3.00

40

40

50

50

> 3.00

≤ 6.00

40

50

50

50

> 6.00

≤ 11.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades
(S185-S235-S275 ≤ 10mm in EN 10025-2:2004)

Category 2

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 20.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades(S275 > 10mm in EN 10025-2:2004)
 and HSLA grades (S315MC in EN 10149-2:1996)

Category 3

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

50

50

60

60

> 2.00

≤ 2.50

50

60

60

60

> 2.50

≤ 3.00

50

60

60

60

> 3.00

≤ 20.00

60

60

70

70

 

Maximum Crown C40 in µm values of HSLA grades
 (S355MC, S420MC, S460MC, S500MC, S550MC in EN 10149-2:1996)

Category 4

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

60

70

70

70

> 2.00

≤ 2.50

60

70

80

80

> 2.50

≤ 3.00

60

70

80

80

> 3.00

≤ 5.00

70

70

80

80

> 5.00

≤ 20.00

80

80

80

80

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights:

Description

Availability

Coil diameter inner non-pickled

762mm

Coil diameter inner pickled

610mm standard

762mm on request

Tolerance on inner diameter

+0/-50mm

Coil diameter outer non-pickled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Max. 2200mm

Min. 1050mm

Coil diameter outer pickled and oiled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Outer diameter

limit 2200mm

Min. 1050mm

Coil weight

Max. 34 tonnes

Additional maximum limits from transport

limits and outer coil diameter

Some HR products may have different

coil weight ranges

KIM: width ≤ 1200mm

15.5 - 23.0 kg/mm width

KIM: 1200 < width ≤ 1700mm

12.1 - 21.7 kg/mm width

KIM: width > 1700mm

11.0 kg/mm width and 12.1 - 21.7 kg/mm width

Minimum tonnage per order

Please refer to price list for order quantity details

Minimum order quantities may apply

 

 

 

 

EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.

Heavy gauge processing

Processing type Decoiling
Thickness range (mm) 1.4 - 25.4
Width range (mm) 300 - 2600
Length range up to 18.4m
Locations UK
Netherlands

 

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands


For further information please visit our Service Centre webpages.

 

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades DownloadsTSE

Download

Download:

 

EN-Engineering-Product-Hot-Rolled-Structural steel-S275JR/J0/J2 TSE

S275JR/J0/J2
Specification details for S275JR/J0/J2

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades OverviewTSE

Overview

Availability

Structural steel products are available as follows:

  • As-rolled (+AR)

  • Normalised rolling (+N)

  • Suitable for cold forming (C)

  • Suitable for post-galvanising (Class 1)

  • Weathering steel (W)

Relationship with standards

Hot-rolled structural steel complies with European standard EN 10025: 2004 and is available in the grades shown in the table below.

If normalised rolling (+N) or cold forming (C) is required, please specify when ordering. In these cases, this should be indicated by adding the relevant letter to the grade at the time of ordering (for example: S355J0C+AR). Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

European standard Charpy Weathering steel European standard As Rolled Normalised Suitable for Cold forming Suitable for Post galvanising
EN 10025-2: 2004 JR J0 J2 K2 W EN 10025-2: 2006 AR +N C Class I
S185             Y   Y Y
S235 Y Y Y       Y Y Y Y
S275 Y Y Y       Y Y Y Y
S355 Y Y Y Y Y   Y Y Y Y
 

The CE mark

The CE mark is a symbol devised by the European Council to signify that a product meets the conditions of the applicable council directives. These conditions aim to ensure that the product is reliable and safe. Products that are “produced for incorporation in a permanent manner in construction works” fall under the Construction Products Directive. Hot-rolled steels covered by EN 10025: 2004 are used in such “works” and are therefore covered by the directive. For these products, Tata Steel’s test certificates bear the CE mark and Tata Steel has issued a certified Declaration of Performance (DoP). All the structural products produced by Tata Steel in Europe are CE-marked except for S185+AR.
 

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition

non-pickled

pickled

pickled and oiled

Mill edges

Yes

Yes

Yes

Trimmed edges

-

Yes

Yes

Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.

Surface aspects

Description

Availability

Surface finish

Coils are available in non-pickled and pickled finish

Oiling

Pickled finish is available with rolling or preservative oil applied

 

Oil weight normally 0.5-2.5 g/m2

Alternative oiling ranges are available – please contact us for details.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE

Supply Conditions

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
Trimmed edges available in thicknesses up to 8.0 mm.
Please contact us regarding other specifications we may have that meet your needs.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling
or preservative oil applied. 
Oil weight normally 0.5-2.5 g/m2
Alternative oiling ranges are available.
Please contact us for details.
 

Certification

Test certificates 2.2/3.1 are available according to EN 10204.         

EN-Engineering-Product-Hot-Rolled-Structural Steel-S275JR/J0/J2-Properties TSE

Properties

Mechanical Properties

The values shown for strength and elongation in the table below are for test pieces taken transverse to the rolling direction; those for the impact test are for test pieces taken in the rolling direction.

EN 10025-2: 2004   Grade S275JR/J0/J2
Min. yield strength 1, 2 ReH (N/mm2) t ≤ 16 275
16 < t ≤ 20 265
Tensile strength Rm (N/mm2) t < 3 430 - 580
3 ≤ t ≤ 20 410 - 560
Elongation % 1.5 < t ≤ 2 15
2 < t ≤ 2.5 16
2.5 < t < 3 17
3 ≤ t ≤ 20 21
Impact strength     JR 3 / J0 / J2
Temp. °C   20 / 0 / -20
Min. energy J   27
1. Upper yield strength or 0.2% proof stress applies.
2. For thicknesses > 16 mm, the ReH value is decreased by 10 N/mm2.
3. The impact properties of quality JR products are verified only when specified at the time of enquiry or order.
   Impact strengths apply to thicknesses > 6 mm and are for standard test pieces only. Please contact us for details.
For the mechanical properties of cold-forming qualities, please consult us.
Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 mm. L0 = 5.65√S0 for t ≥ 3 mm.
t – material thickness in mm.

Impact strength

Impact tests can be performed for thicknesses ≥ 6.0 mm. Please contact us for details.
 

Chemical composition

Structural steel meets the requirements of the cast analysis in the standard, as shown in the table below.

The steel grades supplied by Tata Steel are always fully killed.
Tata Steel does not supply steel with increased copper content.

  Grade S275JR
C Max. 0.21
Mn Max. 1.50
P Max. 0.035
S Max. 0.035
Si Max.
N Max. 0.012
Cu Max. 0.55
The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020% or if sufficient other nitrogen-binding elements are present.
The nitrogen-binding elements shall be mentioned in the inspection document.
For the chemical composition of cold-forming qualities, please consult us.
The chemical composition of steels suitable for galvanising complies with EN 10025-2: 2004.
All values are in weight%.
 

Suitability for cold forming

If chemistry suitable for cold forming (+C) is required, this must be specified when the material is ordered.
Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.
 

Suitability for galvanising

If chemistry suitable for post-galvanising (Class 1) is required, this must be specified when the material is ordered.

EN-Engineering-Product-Hot-Rolled-Structural Steel-S275-Dimensions TSE

Dimensions

Dimensional capability - non-pickled

Dimensions in mm.

Thickness Max. width
From - up to S275JR/J0/J2
1.49 - 1.50 1170
1.50 - 1.60 1260
1.60 - 1.70 1280
1.70 - 1.80 1370
1.80 - 1.90 1500
1.90 - 2.00 1510
2.00 - 2.20 1590
2.20 - 2.40 1730
2.40 - 2.60 1810
2.60 - 2.70 1880
2.70 - 2.80 1920
2.80 - 3.00 1960
3.00 - 3.20 2030
3.20 - 20.00 2070 1
All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm except for thicknesses above 20 mm where the min. width is 1500 mm.

1. S275 JR/J0/J2 + N available for thicknesses ≤ 10 mm.
Other dimensions are available - please contact us.
 

Dimensional capability - pickled

Dimensions in mm.

Thickness Max. width
From - up to S275JR/J0/J2
1.50 - 1.57 1260
1.57 - 1.60 1265
1.60 - 1.70 1280
1.70 - 1.80 1370
1.80 - 1.90 1499
1.90 - 2.00 1510
2.00 - 2.20 1590
2.20 - 2.40 1730
2.40 - 2.60 1810
2.60 - 2.70 1880
2.70 - 2.80 1920
2.80 - 3.00 1960
3.00 - 3.20 2030
3.20 - 10.10 2070
10.10 - 15.25 1600 1
All grades are available in the as-rolled (+AR), normalized rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm. Widths smaller than 900 mm are available - please contact us.
1. S275 JR/J0/J2 + N available for thicknesses ≤ 10 mm.
Thicknesses up to 20 mm may be available - please contact us.
 

Tolerances

Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.

Tighter tolerances are available, please contact us.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE

Shape and dimensional tolerances

Shape and dimensional tolerances

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:

length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

 

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.

Tighter tolerances are available as shown below:

Product type Thickness tolerances available
  (% of full EN 10051:2010 tolerance)
  100% 75% 66% 60% 50% 33%

Steel for forming

Yes

Yes

Yes

Yes

Yes

Yes 1

High-strength low-alloy
(HSLA EN 10149-2)

Yes

Yes

Yes

Yes

Yes

Yes 1

Ympress® HSLA

 

 

 

 

Yes

Yes 1

Ympress® Laser

 

 

 

 

Yes

Yes 1

Structural steel

Yes

Yes

Yes

Yes

Yes

Yes 1

Boron manganese steel Yes Yes Yes Yes Yes  

Case-hardening steel

Yes

Yes

Yes

Yes

Yes

 

High-carbon steel

Yes

 

 

 

 

 

Dual phase steel

Yes

 

 

 

 

 

Hot forming steel

Yes

 

 

 

 

 

Valast® abrasion resistant steel

Yes

Yes

Yes

Yes

Yes

 

Steel for pressure vessels

Yes

 

 

 

 

 

Steel for gas cylinders

Yes

 

 

 

 

 

Steel for line pipe

Yes

 

 

 

 

 

Ship plate

Yes

 

 

 

 

 

1. Available for certain grades and thicknesses between 3.0mm and 6.0mm.
Please contact us on the availability of special tolerances to meet your requirements.
 
Tolerances on thickness for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.13

± 0.14

± 0.16

-

> 2.00

≤ 2.50

± 0.14

± 0.16

± 0.17

± 0.19

> 2.50

≤ 3.00

± 0.15

± 0.17

± 0.18

± 0.20

> 3.00

≤ 4.00

± 0.17

± 0.18

± 0.20

± 0.20

> 4.00

≤ 5.00

± 0.18

± 0.20

± 0.21

± 0.22

> 5.00

≤ 6.00

± 0.20

± 0.21

± 0.22

± 0.23

> 6.00

≤ 8.00

± 0.22

± 0.23

± 0.23

± 0.26

> 8.00

≤ 11.00

± 0.24

± 0.25

± 0.25

± 0.28

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
Re ≤ 300 N/mm2 (category A)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800
 

≤ 2.00

± 0.17

± 0.19

± 0.21

-

> 2.00

≤ 2.50

± 0.18

± 0.21

± 0.23

± 0.25

> 2.50

≤ 3.00

± 0.20

± 0.22

± 0.24

± 0.26

> 3.00

≤ 4.00

± 0.22

± 0.24

± 0.26

± 0.27

> 4.00

≤ 5.00

± 0.24

± 0.26

± 0.28

± 0.29

> 5.00

≤ 6.00

± 0.26

± 0.28

± 0.29

± 0.31

> 6.00

≤ 8.00

± 0.29

± 0.30

± 0.31

± 0.35

> 8.00

≤ 10.00

± 0.32

± 0.33

± 0.34

± 0.40

> 10.00

≤ 12.50

± 0.35

± 0.36

± 0.37

± 0.43

> 12.50

≤ 15.00

± 0.37

± 0.38

± 0.40

± 0.46

> 15.00

≤ 25.00

± 0.40

± 0.42

± 0.45

± 0.50

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
300 N/mm2 < Re ≤ 360 N/mm2 (category B)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.20

± 0.22

± 0.24

-

> 2.00

≤ 2.50

± 0.21

± 0.24

± 0.26

± 0.29

> 2.50

≤ 3.00

± 0.23

± 0.25

± 0.28

± 0.30

> 3.00

≤ 4.00

± 0.25

± 0.28

± 0.30

± 0.31

> 4.00

≤ 5.00

± 0.28

± 0.30

± 0.32

± 0.33

> 5.00

≤ 6.00

± 0.30

± 0.32

± 0.33

± 0.36

> 6.00

≤ 8.00

± 0.33

± 0.35

± 0.36

± 0.40

> 8.00

≤ 10.00

± 0.37

± 0.38

± 0.39

± 0.46

> 10.00

≤ 12.50

± 0.40

± 0.41

± 0.43

± 0.49

> 12.50

≤ 15.00

± 0.43

± 0.44

± 0.46

± 0.53

> 15.00

≤ 25.00

± 0.46

± 0.48

± 0.52

± 0.58

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
360 N/mm2 < Re ≤ 420 N/mm2 (category C)
Nominal thickness

Tolerances for a nominal width of

≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.22

± 0.25

± 0.27

-

> 2.00

≤ 2.50

± 0.23

± 0.27

± 0.30

± 0.33

> 2.50

≤ 3.00

± 0.26

± 0.29

± 0.31

± 0.34

> 3.00

≤ 4.00

± 0.29

± 0.31

± 0.34

± 0.35

> 4.00

≤ 5.00

± 0.31

± 0.34

± 0.36

± 0.38

> 5.00

≤ 6.00

± 0.34

± 0.36

± 0.38

± 0.40

> 6.00

≤ 8.00

± 0.38

± 0.39

± 0.40

± 0.46

> 8.00

≤ 10.00

± 0.42

± 0.43

± 0.44

± 0.52

> 10.00

≤ 12.50

± 0.46

± 0.47

± 0.48

± 0.56

> 12.50

≤ 15.00

± 0.48

± 0.49

± 0.52

± 0.60

> 15.00

≤ 25.00

± 0.52

± 0.55

± 0.59

± 0.65

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
420 N/mm2 < Re ≤ 900 N/mm2 (category D)

Nominal thickness

Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.24

± 0.27

± 0.29

-

> 2.00

≤ 2.50

± 0.25

± 0.29

± 0.32

± 0.35

> 2.50

≤ 3.00

± 0.28

± 0.31

± 0.34

± 0.36

> 3.00

≤ 4.00

± 0.31

± 0.34

± 0.36

± 0.38

> 4.00

≤ 5.00

± 0.34

± 0.36

± 0.39

± 0.41

> 5.00

≤ 6.00

± 0.36

± 0.39

± 0.41

± 0.43

> 6.00

≤ 8.00

± 0.41

± 0.42

± 0.43

± 0.49

> 8.00

≤ 10.00

± 0.45

± 0.46

± 0.48

± 0.56

> 10.00

≤ 12.50

± 0.49

± 0.50

± 0.52

± 0.60

> 12.50

≤ 15.00

± 0.52

± 0.53

± 0.56

± 0.64

> 15.00

≤ 25.00

± 0.56

± 0.59

± 0.63

± 0.70

All dimensions are mm.

Tolerances on width

Tolerances in mm.

Nominal width w
Mill edges Trimmed edges
lower upper lower upper

 w ≤ 1200

0

20

0

3

 1200 < w ≤ 1850

0

20

0

5

 w > 1850

0

25

0

6

Tolerances  in mm for wide strip and slit wide strip
The tolerances for wide strip and slit wide strip comply with standard EN 10051:2010.

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

Edge camber

The deviation from the edge over a length of 5000mm:

• with mill edges, no more than 20mm
• with trimmed edges, no more than 15mm

Flatness

Requirements as regards flatness can be agreed at the time of enquiry.

Option for maximum crown values

The following high crown C40 options available for hot-rolled products.

Crown values on the C20-position as well as minimum crown values on both C20 and C40 position are also available on request.

 

Maximum Crown C40 in µm values for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)

Category 1

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 3.00

40

40

50

50

> 3.00

≤ 6.00

40

50

50

50

> 6.00

≤ 11.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades
(S185-S235-S275 ≤ 10mm in EN 10025-2:2004)

Category 2

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 20.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades(S275 > 10mm in EN 10025-2:2004)
 and HSLA grades (S315MC in EN 10149-2:1996)

Category 3

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

50

50

60

60

> 2.00

≤ 2.50

50

60

60

60

> 2.50

≤ 3.00

50

60

60

60

> 3.00

≤ 20.00

60

60

70

70

 

Maximum Crown C40 in µm values of HSLA grades
 (S355MC, S420MC, S460MC, S500MC, S550MC in EN 10149-2:1996)

Category 4

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

60

70

70

70

> 2.00

≤ 2.50

60

70

80

80

> 2.50

≤ 3.00

60

70

80

80

> 3.00

≤ 5.00

70

70

80

80

> 5.00

≤ 20.00

80

80

80

80

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights:

Description

Availability

Coil diameter inner non-pickled

762mm

Coil diameter inner pickled

610mm standard

762mm on request

Tolerance on inner diameter

+0/-50mm

Coil diameter outer non-pickled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Max. 2200mm

Min. 1050mm

Coil diameter outer pickled and oiled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Outer diameter

limit 2200mm

Min. 1050mm

Coil weight

Max. 34 tonnes

Additional maximum limits from transport

limits and outer coil diameter

Some HR products may have different

coil weight ranges

KIM: width ≤ 1200mm

15.5 - 23.0 kg/mm width

KIM: 1200 < width ≤ 1700mm

12.1 - 21.7 kg/mm width

KIM: width > 1700mm

11.0 kg/mm width and 12.1 - 21.7 kg/mm width

Minimum tonnage per order

Please refer to price list for order quantity details

Minimum order quantities may apply

 

 

 

 

EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.

Heavy gauge processing

Processing type Decoiling
Thickness range (mm) 1.4 - 25.4
Width range (mm) 300 - 2600
Length range up to 18.4m
Locations UK
Netherlands

 

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands


For further information please visit our Service Centre webpages.

 

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades DownloadsTSE

Download

Download:

 

EN-Engineering-Product-Hot-Rolled-Structural steel-S355JR/J0/J2/K2 TSE

S355JR/J0/J2/K2
Specification details for S355JR/J0/J2/K2

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades OverviewTSE

Overview

Availability

Structural steel products are available as follows:

  • As-rolled (+AR)

  • Normalised rolling (+N)

  • Suitable for cold forming (C)

  • Suitable for post-galvanising (Class 1)

  • Weathering steel (W)

Relationship with standards

Hot-rolled structural steel complies with European standard EN 10025: 2004 and is available in the grades shown in the table below.

If normalised rolling (+N) or cold forming (C) is required, please specify when ordering. In these cases, this should be indicated by adding the relevant letter to the grade at the time of ordering (for example: S355J0C+AR). Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.

European standard Charpy Weathering steel European standard As Rolled Normalised Suitable for Cold forming Suitable for Post galvanising
EN 10025-2: 2004 JR J0 J2 K2 W EN 10025-2: 2006 AR +N C Class I
S185             Y   Y Y
S235 Y Y Y       Y Y Y Y
S275 Y Y Y       Y Y Y Y
S355 Y Y Y Y Y   Y Y Y Y
 

The CE mark

The CE mark is a symbol devised by the European Council to signify that a product meets the conditions of the applicable council directives. These conditions aim to ensure that the product is reliable and safe. Products that are “produced for incorporation in a permanent manner in construction works” fall under the Construction Products Directive. Hot-rolled steels covered by EN 10025: 2004 are used in such “works” and are therefore covered by the directive. For these products, Tata Steel’s test certificates bear the CE mark and Tata Steel has issued a certified Declaration of Performance (DoP). All the structural products produced by Tata Steel in Europe are CE-marked except for S185+AR.
 

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition

non-pickled

pickled

pickled and oiled

Mill edges

Yes

Yes

Yes

Trimmed edges

-

Yes

Yes

Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.

Surface aspects

Description

Availability

Surface finish

Coils are available in non-pickled and pickled finish

Oiling

Pickled finish is available with rolling or preservative oil applied

 

Oil weight normally 0.5-2.5 g/m2

Alternative oiling ranges are available – please contact us for details.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE

Supply Conditions

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
Trimmed edges available in thicknesses up to 8.0 mm.
Please contact us regarding other specifications we may have that meet your needs.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling
or preservative oil applied. 
Oil weight normally 0.5-2.5 g/m2
Alternative oiling ranges are available.
Please contact us for details.
 

Certification

Test certificates 2.2/3.1 are available according to EN 10204.         

EN-Engineering-Product-Hot-Rolled-Structural Steel-S355JR/J0/J2/K2-Properties TSE

Properties

Mechanical Properties

The values shown for strength and elongation in the table below are for test pieces taken transverse to the rolling direction; those for the impact test are for test pieces taken in the rolling direction.

EN 10025-2: 2004   Grade S355JR/J0/J0W/J2/J2W/K2
Min. yield strength 1, 2 ReH (N/mm2) t ≤ 16 355
16 < t ≤ 20 345
Tensile strength Rm (N/mm2 t < 3 510 - 680
3 ≤ t ≤ 20 470 - 630
Elongation % 1.5 < t ≤ 2 14
2 < t ≤ 2.5 15
2.5 < t < 3 16
3 ≤ t ≤ 20 20
      JR3/J0/J0W/J2/J2W/K2
Impact test Temp. °C   20 / 0 / -20 / -20
Min. energy J   27 / 27 / 27 / 40
1. Upper yield strength or 0.2% proof stress applies.
2. For thicknesses > 16 mm, the ReH value is decreased by 10 N/mm2.
3. The impact properties of quality JR products are verified only when specified at the time of enquiry or order.
   Impact strengths apply to thicknesses > 6 mm and are for standard test pieces only. Please contact us for details.
   For the mechanical properties of cold-forming qualities, please consult us.
Tensile tests may be carried out on non-proportional test pieces as specified in EN 10025-1: 2004.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 mm. L0 = 5.65√S0 for t ≥ 3 mm.
t – material thickness in mm.
 

Chemical composition

Structural steel meets the requirements of the cast analysis in the standard, as shown in the table below.

The steel grades supplied by Tata Steel are always fully killed.
Tata Steel does not supply steel with increased copper content.

Grade   S355JR S355K2 S355J0W/J2W
C Max. 0.24 0.2 0.16
Mn Max. 1.6 1.6 1.5
P Max. 0.035 0.025 0.025
S Max. 0.035 0.025 0.008
Si Max. 0.55 0.55 0.5
N Max. 0.012 - 0.012
Cu Max. 0.55 0.55 0.4
The maximum value for nitrogen does not apply if the chemical composition shows a minimum total aluminium content of 0.020% or if sufficient other nitrogen-binding elements are present.
The nitrogen-binding elements shall be mentioned in the inspection document.
For the chemical composition of cold-forming qualities, please consult us.
The chemical composition of steels suitable for galvanising complies with EN 10025-2: 2004.
All values are in weight%.
 

Suitability for cold forming

If chemistry suitable for cold forming (+C) is required, this must be specified when the material is ordered.
Cold forming cannot be guaranteed for structural steel that is not specified as cold-formable.
 

Suitability for galvanising

If chemistry suitable for post-galvanising (Class 1) is required, this must be specified when the material is ordered.
As standard, grades S355JR+AR and S355J2(C)+N in thickness 25 mm are supplied with such a chemistry.

EN-Engineering-Product-Hot-Rolled-Structural Steel-S355JR/J0/J2/K2-Dimensions TSE

Dimensions

Dimensional capability - non-pickled

Dimensions in mm.

Thickness Max. width
From - up to S355JR/J0/J2/K2 S355J0W/J2W
1.57 - 1.60 1010 -
1.60 - 1.70 1050 -
1.70 - 1.80 1150 -
1.80 - 2.00 1250 -
2.00 - 2.20 1380 -
2.20 - 2.40 1525 -
2.40 - 2.60 1630 -
2.60 - 2.70 1710 -
2.70 - 2.80 1730 -
2.80 - 3.00 1760 -
3.00 - 3.20 1790 -
3.20 - 3.50 1840 -
3.50 - 3.65 1900 -
3.65 - 4.00 1930 -
4.00 - 4.40 2000 -
4.40 - 5.00 2070 -
5.00 - 16.50 2070 1 1606
16.50 - 25.00 2070 1 -
All grades are available in the as-rolled (+AR), normalised rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm except for thicknesses above 20 mm where the min. width is 1500 mm.
1. S355JR/J0/J2 + N/AR: thicknesses > 21 mm and ≤ 25 mm are available as cut-to-length.
   S355K2 + N available for thicknesses ≤ 12.70 mm.
Other dimensions are available - please contact us.
 

Dimensional capability - pickled

Dimensions in mm.

Thickness Max. width
From - up to S355JR/J0/J2/K2
1.53 - 1.57 960
1.57 - 1.60 1010
1.60 - 1.70 1050
1.70 - 1.80 1150
1.80 - 2.00 1250
2.00 - 2.20 1380
2.20 - 2.40 1525
2.40 - 2.60 1630
2.60 - 2.70 1710
2.70 - 2.80 1730
2.80 - 3.00 1760
3.00 - 3.20 1790
3.20 - 3.50 1840
3.50 - 3.65 1900
3.65 - 4.00 1930
4.00 - 4.40 2000
4.40 - 10.10 2070
10.10 - 12.10 1600
All grades are available in the as-rolled (+AR), normalised rolling (+N) and suitable for cold forming (C) conditions.
The minimum width is 900 mm. Widths smaller than 900 mm are available - please contact us.
Thicknesses up to 25 mm are available as plate pickled - please contact us.
 

Tolerances

Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.

Tighter tolerances are available, please contact us.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE

Shape and dimensional tolerances

Shape and dimensional tolerances

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:

length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

 

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.

Tighter tolerances are available as shown below:

Product type Thickness tolerances available
  (% of full EN 10051:2010 tolerance)
  100% 75% 66% 60% 50% 33%

Steel for forming

Yes

Yes

Yes

Yes

Yes

Yes 1

High-strength low-alloy
(HSLA EN 10149-2)

Yes

Yes

Yes

Yes

Yes

Yes 1

Ympress® HSLA

 

 

 

 

Yes

Yes 1

Ympress® Laser

 

 

 

 

Yes

Yes 1

Structural steel

Yes

Yes

Yes

Yes

Yes

Yes 1

Boron manganese steel Yes Yes Yes Yes Yes  

Case-hardening steel

Yes

Yes

Yes

Yes

Yes

 

High-carbon steel

Yes

 

 

 

 

 

Dual phase steel

Yes

 

 

 

 

 

Hot forming steel

Yes

 

 

 

 

 

Valast® abrasion resistant steel

Yes

Yes

Yes

Yes

Yes

 

Steel for pressure vessels

Yes

 

 

 

 

 

Steel for gas cylinders

Yes

 

 

 

 

 

Steel for line pipe

Yes

 

 

 

 

 

Ship plate

Yes

 

 

 

 

 

1. Available for certain grades and thicknesses between 3.0mm and 6.0mm.
Please contact us on the availability of special tolerances to meet your requirements.
 
Tolerances on thickness for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.13

± 0.14

± 0.16

-

> 2.00

≤ 2.50

± 0.14

± 0.16

± 0.17

± 0.19

> 2.50

≤ 3.00

± 0.15

± 0.17

± 0.18

± 0.20

> 3.00

≤ 4.00

± 0.17

± 0.18

± 0.20

± 0.20

> 4.00

≤ 5.00

± 0.18

± 0.20

± 0.21

± 0.22

> 5.00

≤ 6.00

± 0.20

± 0.21

± 0.22

± 0.23

> 6.00

≤ 8.00

± 0.22

± 0.23

± 0.23

± 0.26

> 8.00

≤ 11.00

± 0.24

± 0.25

± 0.25

± 0.28

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
Re ≤ 300 N/mm2 (category A)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800
 

≤ 2.00

± 0.17

± 0.19

± 0.21

-

> 2.00

≤ 2.50

± 0.18

± 0.21

± 0.23

± 0.25

> 2.50

≤ 3.00

± 0.20

± 0.22

± 0.24

± 0.26

> 3.00

≤ 4.00

± 0.22

± 0.24

± 0.26

± 0.27

> 4.00

≤ 5.00

± 0.24

± 0.26

± 0.28

± 0.29

> 5.00

≤ 6.00

± 0.26

± 0.28

± 0.29

± 0.31

> 6.00

≤ 8.00

± 0.29

± 0.30

± 0.31

± 0.35

> 8.00

≤ 10.00

± 0.32

± 0.33

± 0.34

± 0.40

> 10.00

≤ 12.50

± 0.35

± 0.36

± 0.37

± 0.43

> 12.50

≤ 15.00

± 0.37

± 0.38

± 0.40

± 0.46

> 15.00

≤ 25.00

± 0.40

± 0.42

± 0.45

± 0.50

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
300 N/mm2 < Re ≤ 360 N/mm2 (category B)
Nominal thickness Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.20

± 0.22

± 0.24

-

> 2.00

≤ 2.50

± 0.21

± 0.24

± 0.26

± 0.29

> 2.50

≤ 3.00

± 0.23

± 0.25

± 0.28

± 0.30

> 3.00

≤ 4.00

± 0.25

± 0.28

± 0.30

± 0.31

> 4.00

≤ 5.00

± 0.28

± 0.30

± 0.32

± 0.33

> 5.00

≤ 6.00

± 0.30

± 0.32

± 0.33

± 0.36

> 6.00

≤ 8.00

± 0.33

± 0.35

± 0.36

± 0.40

> 8.00

≤ 10.00

± 0.37

± 0.38

± 0.39

± 0.46

> 10.00

≤ 12.50

± 0.40

± 0.41

± 0.43

± 0.49

> 12.50

≤ 15.00

± 0.43

± 0.44

± 0.46

± 0.53

> 15.00

≤ 25.00

± 0.46

± 0.48

± 0.52

± 0.58

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
360 N/mm2 < Re ≤ 420 N/mm2 (category C)
Nominal thickness

Tolerances for a nominal width of

≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.22

± 0.25

± 0.27

-

> 2.00

≤ 2.50

± 0.23

± 0.27

± 0.30

± 0.33

> 2.50

≤ 3.00

± 0.26

± 0.29

± 0.31

± 0.34

> 3.00

≤ 4.00

± 0.29

± 0.31

± 0.34

± 0.35

> 4.00

≤ 5.00

± 0.31

± 0.34

± 0.36

± 0.38

> 5.00

≤ 6.00

± 0.34

± 0.36

± 0.38

± 0.40

> 6.00

≤ 8.00

± 0.38

± 0.39

± 0.40

± 0.46

> 8.00

≤ 10.00

± 0.42

± 0.43

± 0.44

± 0.52

> 10.00

≤ 12.50

± 0.46

± 0.47

± 0.48

± 0.56

> 12.50

≤ 15.00

± 0.48

± 0.49

± 0.52

± 0.60

> 15.00

≤ 25.00

± 0.52

± 0.55

± 0.59

± 0.65

All dimensions are mm.
Tolerances on thickness of steel grades with a specified minimum yield strength
420 N/mm2 < Re ≤ 900 N/mm2 (category D)

Nominal thickness

Tolerances for a nominal width of
≤ 1200 > 1200 > 1500 > 1800
≤ 1500 ≤ 1800

 

≤ 2.00

± 0.24

± 0.27

± 0.29

-

> 2.00

≤ 2.50

± 0.25

± 0.29

± 0.32

± 0.35

> 2.50

≤ 3.00

± 0.28

± 0.31

± 0.34

± 0.36

> 3.00

≤ 4.00

± 0.31

± 0.34

± 0.36

± 0.38

> 4.00

≤ 5.00

± 0.34

± 0.36

± 0.39

± 0.41

> 5.00

≤ 6.00

± 0.36

± 0.39

± 0.41

± 0.43

> 6.00

≤ 8.00

± 0.41

± 0.42

± 0.43

± 0.49

> 8.00

≤ 10.00

± 0.45

± 0.46

± 0.48

± 0.56

> 10.00

≤ 12.50

± 0.49

± 0.50

± 0.52

± 0.60

> 12.50

≤ 15.00

± 0.52

± 0.53

± 0.56

± 0.64

> 15.00

≤ 25.00

± 0.56

± 0.59

± 0.63

± 0.70

All dimensions are mm.

Tolerances on width

Tolerances in mm.

Nominal width w
Mill edges Trimmed edges
lower upper lower upper

 w ≤ 1200

0

20

0

3

 1200 < w ≤ 1850

0

20

0

5

 w > 1850

0

25

0

6

Tolerances  in mm for wide strip and slit wide strip
The tolerances for wide strip and slit wide strip comply with standard EN 10051:2010.

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:
length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

Edge camber

The deviation from the edge over a length of 5000mm:

• with mill edges, no more than 20mm
• with trimmed edges, no more than 15mm

Flatness

Requirements as regards flatness can be agreed at the time of enquiry.

Option for maximum crown values

The following high crown C40 options available for hot-rolled products.

Crown values on the C20-position as well as minimum crown values on both C20 and C40 position are also available on request.

 

Maximum Crown C40 in µm values for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)

Category 1

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 3.00

40

40

50

50

> 3.00

≤ 6.00

40

50

50

50

> 6.00

≤ 11.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades
(S185-S235-S275 ≤ 10mm in EN 10025-2:2004)

Category 2

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

40

40

40

40

> 2.00

≤ 2.50

40

40

50

50

> 2.50

≤ 20.00

50

50

50

50

 

Maximum Crown C40 in µm values of structural steel grades(S275 > 10mm in EN 10025-2:2004)
 and HSLA grades (S315MC in EN 10149-2:1996)

Category 3

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

50

50

60

60

> 2.00

≤ 2.50

50

60

60

60

> 2.50

≤ 3.00

50

60

60

60

> 3.00

≤ 20.00

60

60

70

70

 

Maximum Crown C40 in µm values of HSLA grades
 (S355MC, S420MC, S460MC, S500MC, S550MC in EN 10149-2:1996)

Category 4

C40

     
Nominal Thickness

≤ 1200

> 1200

> 1500

> 1800

≤ 1500

≤ 1800

> 1.47

≤ 2.00

60

70

70

70

> 2.00

≤ 2.50

60

70

80

80

> 2.50

≤ 3.00

60

70

80

80

> 3.00

≤ 5.00

70

70

80

80

> 5.00

≤ 20.00

80

80

80

80

 

Dimensions and coil weights

Tata Steel can supply hot-rolled steels with the following minimum and maximum dimensions and weights:

Description

Availability

Coil diameter inner non-pickled

762mm

Coil diameter inner pickled

610mm standard

762mm on request

Tolerance on inner diameter

+0/-50mm

Coil diameter outer non-pickled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Max. 2200mm

Min. 1050mm

Coil diameter outer pickled and oiled

Outer diameter available is 10/7 x width

to reduce possibility of coil tipping over

Outer diameter

limit 2200mm

Min. 1050mm

Coil weight

Max. 34 tonnes

Additional maximum limits from transport

limits and outer coil diameter

Some HR products may have different

coil weight ranges

KIM: width ≤ 1200mm

15.5 - 23.0 kg/mm width

KIM: 1200 < width ≤ 1700mm

12.1 - 21.7 kg/mm width

KIM: width > 1700mm

11.0 kg/mm width and 12.1 - 21.7 kg/mm width

Minimum tonnage per order

Please refer to price list for order quantity details

Minimum order quantities may apply

 

 

 

 

EN-EngineeringAutomotive-Product-Hot-rolled-Heavy+Light further processing TSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times.

Heavy gauge processing

Processing type Decoiling
Thickness range (mm) 1.4 - 25.4
Width range (mm) 300 - 2600
Length range up to 18.4m
Locations UK
Netherlands

 

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands


For further information please visit our Service Centre webpages.

 

EN-Engineering-Product-Hot-Rolled-Structural steel-All grades DownloadsTSE

Download

Download: