Cold-rolled

Ymvit

Tata Steel’s Ymvit® cold-rolled steel for enamelling delivers end product and process benefits including superb coating adhesion and reliable deep drawing. Ymvit Ultra grades provide perfect coating adhesion and improved resistance to carbon boiling and fish scaling. 

Applications include bakeware, barbecues, bathroom furniture, heat-exchange panels, photovoltaic solar panels, domestic appliances, sinks white boards and wall panels.

Ymvit enamelling steel component
Bath tub made from Ymvit product
tata-steel-industry-strip-cold-rolled-Ymvit 01_DSC0747.jpg
tata-steel-industry-strip-cold-rolled-Ymvit Ultra 04_DSC0801.jpg
Product specification
Steel for enamelling is currently available in the following grades

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 01 (DC01EK) TSN

Ymvit 01 (DC01EK)
Specification details for Ymvit 01

EN-Engineering-Product-Cold-rolled-Ymvit enameling-All Grades OverviewTSN

Overview

Relationship with standards

Steel for enamelling complies with the following standards:

Tata Steel

European standard

USA

Ymvit Grade

EN 10209

ASTM A424

Ground Coat Enamelling (if necessary followed by cover coat)

Ymvit 01

DC01EK

-

Ymvit 04

DC04EK

-

Ymvit 04 plus

DC04EK (bath tubs)

-

Two Coat/One Fire and Pore Free Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

Direct White Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 01-Properties TSN

Properties

Properties


Mechanical properties

Steel for enamelling has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

Tata Steel Grade Ymvit 01
EN 10209: 2013 Grade DC01EK
Max. yield strength Re 1,2,3 N/mm² 270
Tensile strength Rm N/mm² 270 - 390
Elongation 3 % 30
r-value r90 -
ravg -
FLD Yes/No -
1. The values of the yield strength are those of the 0.2% yield strength for products that do not present a definite yield point, and the lower yield strength ReL for the other products.
2. For a thickness of 0.5 mm < t < 0.7 mm the maximum value of the yield strength is increased by 20 N/mm² and the minimum elongation after fracture is decreased by 2%.
3. For a thickness of t ≤ 0.5 mm the maximum value of the yield strength is increased by 40 N/mm² and the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 = 80 mm.
4. The r value applies to a thickness of t ≥ 0.5 mm.
   For a thickness of t > 2 mm, the r value is decreased by 0.2.
5. For a thickness of t ≥ 1.5 mm the maximum value of the yield strength is 225 N/mm².
 

Chemical composition

Tata Steel complies with the following cast analysis:

Tata Steel Ymvit Grade Ymvit 01
EN 10209: 2013 Grade DC01EK
C Max. 0.09
Mn Max. 0.50
P Max. 0.030
S Max. 0.050
Ti Max. -
The elements P and Cu are kept within certain limits to ensure that the reactivity of the steel surface is as constant as possible. Under normal conditions this leads to a reproducible enamelling result.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 01-Dimensions TSN

Dimensions

Dimensional capability

Dimensions in mm.

Thickness Max. width
From - up to Ymvit 01
0.37 - 0.40 1540
0.40 - 0.50 1580
0.50 - 0.60 1650
0.60 - 0.70 1720
0.70 - 0.80 1770
0.80 - 0.90 1820
0.90 - 1.00 1870
1.00 - 1.10 1910
1.10 - 1.20 1970
1.20 - 1.30 1980
1.30 - 1.70 2010
1.70 - 1.80 1940
1.80 - 1.90 1910
1.90 - 2.00 1880
2.00 - 2.10 1850
2.10 - 2.20 1830
2.20 - 2.30 1800
2.30 - 2.40 1770
2.40 - 2.50 1750
2.50 - 2.60 1720
2.60 - 2.70 1680
2.70 - 2.80 1640
2.80 - 2.90 1600
2.90 - 3.00 1540
Minimum width is 900 mm.
Other dimensions are available on request – please contact us for details.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 04 (DC04EK) TSN

Ymvit 04 (DC04EK)
Specification details for Ymvit 04

EN-Engineering-Product-Cold-rolled-Ymvit enameling-All Grades OverviewTSN

Overview

Relationship with standards

Steel for enamelling complies with the following standards:

Tata Steel

European standard

USA

Ymvit Grade

EN 10209

ASTM A424

Ground Coat Enamelling (if necessary followed by cover coat)

Ymvit 01

DC01EK

-

Ymvit 04

DC04EK

-

Ymvit 04 plus

DC04EK (bath tubs)

-

Two Coat/One Fire and Pore Free Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

Direct White Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 04-Properties TSN

Properties

Properties


Mechanical properties

Steel for enamelling has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

Tata Steel Grade Ymvit 04
EN 10209: 2013  Grade DC04EK
Max. yield strength Re 1,2,3 N/mm² 220 6
Tensile strength Rm N/mm² 270 - 350
Elongation 3 % 36
r-value r90 -
ravg -
FLD Yes/No -
1. The values of the yield strength are those of the 0.2% yield strength for products that do not present a definite yield point, and the lower yield strength ReL for the other products.
2. For a thickness of 0.5 mm < t < 0.7 mm the maximum value of the yield strength is increased by 20 N/mm² and the minimum elongation after fracture is decreased by 2%.
3. For a thickness of t ≤ 0.5 mm the maximum value of the yield strength is increased by 40 N/mm² and the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 = 80 mm.
4. The r value applies to a thickness of t ≥ 0.5 mm.
   For a thickness of t > 2 mm, the r value is decreased by 0.2.
5. For a thickness of t ≥ 1.5 mm the maximum value of the yield strength is 225 N/mm².
6. For design purposes, a lower yield strength ReL of at least 120 N/mm² can be assumed.
 

Chemical composition

Tata Steel complies with the following cast analysis:

Tata Steel Ymvit Grade Ymvit 04
EN 10209: 2013 Grade DC04EK
C Max. 0.08
Mn Max. 0.40
P Max. 0.030
S Max. 0.050
Ti Max. -
The elements P and Cu are kept within certain limits to ensure that the reactivity of the steel surface is as constant as possible. Under normal conditions this leads to a reproducible enamelling result.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 04-Dimensions TSN

Dimensions

Dimensional capability

Dimensions in mm.

Thickness Max. width
From - up to Ymvit 04
0.37 - 0.40 1500
0.40 - 0.50 1540
0.50 - 0.60 1610
0.60 - 0.70 1680
0.70 - 0.80 1730
0.80 - 0.90 1780
0.90 - 1.00 1830
1.00 - 1.10 1900
1.10 - 1.20 1960
1.20 - 1.30 1970
1.30 - 1.70 2000
1.70 - 1.80 1930
1.80 - 1.90 1900
1.90 - 2.00 1870
2.00 - 2.10 1840
2.10 - 2.20 1820
2.20 - 2.30 1790
2.30 - 2.40 1760
2.40 - 2.50 1740
2.50 - 2.60 1710
2.60 - 2.70 1670
2.70 - 2.80 1630
2.80 - 2.90 1590
2.90 - 3.00 1530
Minimum width is 900 mm.
Other dimensions are available on request – please contact us for details.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 04 plus (DC04EK-bath tubs) TSN

Ymvit 04 plus (DC04EK - bath tubs)
Specification details for Ymvit 04 plus

EN-Engineering-Product-Cold-rolled-Ymvit enameling-All Grades OverviewTSN

Overview

Relationship with standards

Steel for enamelling complies with the following standards:

Tata Steel

European standard

USA

Ymvit Grade

EN 10209

ASTM A424

Ground Coat Enamelling (if necessary followed by cover coat)

Ymvit 01

DC01EK

-

Ymvit 04

DC04EK

-

Ymvit 04 plus

DC04EK (bath tubs)

-

Two Coat/One Fire and Pore Free Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

Direct White Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 04 plus-Properties TSN

Properties

Properties


Mechanical properties

Steel for enamelling has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

Tata Steel Grade Ymvit 04 plus
EN 10209: 2013 Grade DC04EK
Max. yield strength Re 1,2,3 N/mm² 210
Tensile strength Rm N/mm² 270 - 350
Elongation 3 % 38
r-value r90 -
ravg -
FLD Yes/No -
1. The values of the yield strength are those of the 0.2% yield strength for products that do not present a definite yield point, and the lower yield strength ReL for the other products.
2. For a thickness of 0.5 mm < t < 0.7 mm the maximum value of the yield strength is increased by 20 N/mm² and the minimum elongation after fracture is decreased by 2%.
3. For a thickness of t ≤ 0.5 mm the maximum value of the yield strength is increased by 40 N/mm² and the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 = 80 mm.
4. The r value applies to a thickness of t ≥ 0.5 mm.
   For a thickness of t > 2 mm, the r value is decreased by 0.2.
5. For a thickness of t ≥ 1.5 mm the maximum value of the yield strength is 225 N/mm².
 

Chemical composition

Tata Steel complies with the following cast analysis:

Tata Steel Ymvit Grade Ymvit 04 plus
EN 10209: 2013 Grade DC04EK
C Max. 0.08
Mn Max. 0.40
P Max. 0.030
S Max. 0.050
Ti Max. -
The elements P and Cu are kept within certain limits to ensure that the reactivity of the steel surface is as constant as possible. Under normal conditions this leads to a reproducible enamelling result.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit 04 plus-Dimensions TSN

Dimensions

Dimensional capability

Dimensions in mm.

Thickness Max. width
From - up to Ymvit 04 plus
0.80 - 0.90 1780
0.90 - 1.00 1830
1.00 - 1.10 1850
1.10 - 1.20 1820
1.20 - 1.30 1780
1.30 - 1.40 1740
1.40 - 1.50 1720
1.50 - 1.60 1680
1.60 - 1.70 1660
1.70 - 1.80 1620
1.80 - 1.90 1600
1.90 - 2.00 1570
2.00 - 2.10 1530
2.10 - 2.60 1500
Minimum width is 900 mm.
Other dimensions are available on request – please contact us for details.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Ultra 03 (DC03ED) TSN

Ymvit Ultra 03 (DC03ED)
Specification details for Ymvit Ultra 03

EN-Engineering-Product-Cold-rolled-Ymvit enameling-All Grades OverviewTSN

Overview

Relationship with standards

Steel for enamelling complies with the following standards:

Tata Steel

European standard

USA

Ymvit Grade

EN 10209

ASTM A424

Ground Coat Enamelling (if necessary followed by cover coat)

Ymvit 01

DC01EK

-

Ymvit 04

DC04EK

-

Ymvit 04 plus

DC04EK (bath tubs)

-

Two Coat/One Fire and Pore Free Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

Direct White Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Ultra 03-Properties TSN

Properties

Properties


Mechanical properties

Steel for enamelling has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

Tata Steel Grade Ymvit Ultra 03
EN 10209: 2013 Grade DC03ED
Max. yield strength Re 1,2,3 N/mm² 240 6
Tensile strength Rm N/mm² 270 - 370
Elongation 3 % 34
r-value r90 -
ravg -
FLD Yes/No -
1. The values of the yield strength are those of the 0.2% yield strength for products that do not present a definite yield point, and the lower yield strength ReL for the other products.
2. For a thickness of 0.5 mm < t < 0.7 mm the maximum value of the yield strength is increased by 20 N/mm² and the minimum elongation after fracture is decreased by 2%.
3. For a thickness of t ≤ 0.5 mm the maximum value of the yield strength is increased by 40 N/mm² and the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 = 80 mm.
4. The r value applies to a thickness of t ≥ 0.5 mm.
   For a thickness of t > 2 mm, the r value is decreased by 0.2.
5. For a thickness of t ≥ 1.5 mm the maximum value of the yield strength is 225 N/mm².
6. For design purposes, a lower yield strength ReL of at least 120 N/mm² can be assumed.
 

Chemical composition

Tata Steel complies with the following cast analysis:

Tata Steel Ymvit Grade Ymvit Ultra 03
EN 10209: 2013 Grade DC03ED
C Max. 0.004
Mn Max. 0.40
P Max. 0.035
S Max. 0.050
Ti Max. -
The elements P and Cu are kept within certain limits to ensure that the reactivity of the steel surface is as constant as possible. Under normal conditions this leads to a reproducible enamelling result.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Ultra 03-Dimensions TSN

Dimensions

Dimensional capability

Dimensions in mm.

Thickness Max. width
From - up to Ymvit Ultra 03
0.40 - 0.50 1900
0.50 - 0.60 1940
0.60 - 1.50 1960
1.50 - 1.60 1860
1.60 - 1.70 1760
1.70 - 1.80 1660
1.80 - 1.90 1580
1.90 - 2.00 1510
2.00 - 2.10 1430
Minimum width is 900 mm.
Other dimensions are available on request – please contact us for details.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Ultra 04 (DC04ED) TSN

Ymvit Ultra 04 (DC04ED)
Specification details for Ymvit Ultra 04

EN-Engineering-Product-Cold-rolled-Ymvit enameling-All Grades OverviewTSN

Overview

Relationship with standards

Steel for enamelling complies with the following standards:

Tata Steel

European standard

USA

Ymvit Grade

EN 10209

ASTM A424

Ground Coat Enamelling (if necessary followed by cover coat)

Ymvit 01

DC01EK

-

Ymvit 04

DC04EK

-

Ymvit 04 plus

DC04EK (bath tubs)

-

Two Coat/One Fire and Pore Free Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

Direct White Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Ultra 04-Properties TSN

Properties

Properties


Mechanical properties

Steel for enamelling has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

Tata Steel Grade Ymvit Ultra 04
EN 10209: 2013 Grade DC04ED
Max. yield strength Re 1,2,3 N/mm² 210 5, 6
Tensile strength Rm N/mm² 270 - 350
Elongation 3 % 38
r-value r90 -
ravg -
FLD Yes/No Yes
1. The values of the yield strength are those of the 0.2% yield strength for products that do not present a definite yield point, and the lower yield strength ReL for the other products.
2. For a thickness of 0.5 mm < t < 0.7 mm the maximum value of the yield strength is increased by 20 N/mm² and the minimum elongation after fracture is decreased by 2%.
3. For a thickness of t ≤ 0.5 mm the maximum value of the yield strength is increased by 40 N/mm² and the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 = 80 mm.
4. The r value applies to a thickness of t ≥ 0.5 mm.
   For a thickness of t > 2 mm, the r value is decreased by 0.2.
5. For a thickness of t ≥ 1.5 mm the maximum value of the yield strength is 225 N/mm².
6. For design purposes, a lower yield strength ReL of at least 120 N/mm² can be assumed.
 

Chemical composition

Tata Steel complies with the following cast analysis:

Tata Steel Ymvit Grade Ymvit Ultra 04
EN 10209: 2013 Grade DC04ED
C Max. 0.004
Mn Max. 0.40
P Max. 0.030
S Max. 0.050
Ti Max. -
The elements P and Cu are kept within certain limits to ensure that the reactivity of the steel surface is as constant as possible. Under normal conditions this leads to a reproducible enamelling result.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Ultra 04-Dimensions TSN

Dimensions

Dimensional capability

Dimensions in mm.

Thickness Max. width
From - up to Ymvit Ulra 04
0.40 - 0.50 1900
0.50 - 0.60 1940
0.60 - 1.50 1960
1.50 - 1.60 1860
1.60 - 1.70 1760
1.70 - 1.80 1660
1.80 - 1.90 1580
1.90 - 2.00 1510
2.00 - 2.10 1430
Minimum width is 900 mm.
Other dimensions are available on request – please contact us for details.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.
 

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Extra 06 (DC06ED) TSN

Ymvit Extra 06 (DC06ED)
Specification details for Ymvit Extra 06

EN-Engineering-Product-Cold-rolled-Ymvit enameling-All Grades OverviewTSN

Overview

Relationship with standards

Steel for enamelling complies with the following standards:

Tata Steel

European standard

USA

Ymvit Grade

EN 10209

ASTM A424

Ground Coat Enamelling (if necessary followed by cover coat)

Ymvit 01

DC01EK

-

Ymvit 04

DC04EK

-

Ymvit 04 plus

DC04EK (bath tubs)

-

Two Coat/One Fire and Pore Free Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

Direct White Enamelling

Ymvit Ultra 03

DC03ED

type I CS

Ymvit Ultra 04

DC04ED

type I DS

Ymvit Extra 06

DC06ED

type III IF

 

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Surface aspectsTSE

Surface aspects

Surface quality

 

Surface quality A

Defects that do not influence the formability or the application of surface coatings are permitted. They are defects such as pores, minor scratches, slight indentations, small grooves or slight discolouration. 

Surface quality B

The better side must be free of defects that can spoil the uniform appearance of a high-quality paint or of an electrolytic coating. The other side must at least conform to surface quality A. Not all combinations of thickness and width are available in surface quality B. Please contact us for details. 

Inspected side

As a rule, the upper side of the strip is inspected; on request, the strip can be wound so that the inspected side is the underside.

 

Surface texture/roughness

Cold-rolled annealed and skin-passed steel is available in several surface textures. Unless specified otherwise, Tata Steel will supply normal roughness. The table below shows the range of surface textures according to EN 10130:2006.

 

 

Roughness Ra (µm)

EN 10130: 2006

Symbol

cut off 0.8 mm

extra-bright 1

-

≤ 0.3

bright

b

≤ 0.4

semi-bright

g

≤ 0.9

normal

m

0.6 - 1.9

rough

r

> 1.6

extra-rough 2

-

3.5 - 5

1. Not in EN 10130:2006 - Tata Steel’s own specification. Please contact us regarding the availability
2. Not in EN 10130:2006 - Tata Steel’s own specification, measured with a cut off of 2.5 mm
Other surface textures are available to meet your requirements - please contact us for details.

Preservative oil

The standard oil applied by Tata Steel acts as a protective coating. Other types of oil may be available to meet your requirement.
Tata Steel offers a range of oiling levels from 0.25 - 1.7 g/m2 per side.
Other oiling levels are available on request. Tata Steel is not responsible for the risk of corrosion during storage or shipment if material is ordered in the un-oiled condition.

Surface cleanliness

Tata Steel can guarantee improved surface cleanliness on request for batch-annealed products. The cleanliness is tested with a tape test, in which the loss of reflection is measured. The reflection gives an indication of the oil residue on the annealed product. Two levels of loss of reflectivity are available for batch annealed products: a maximum of 20% or a maximum of 30%. Continuously-annealed products typically exhibit a loss of reflection up to around 10%.

 

 

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Extra 06-Properties TSN

Properties

Properties


Mechanical properties

Steel for enamelling has the following mechanical properties (skin-passed) - these are measured transverse to the rolling direction:

Tata Steel Grade Ymvit Extra 06
EN 10209: 2013 Grade DC06ED
Max. yield strength Re 1,2,3 N/mm² 190 6
Tensile strength Rm N/mm² 270 - 350
Elongation 3 % 38
r-value r90 1.9
ravg 1.6
FLD Yes/No Yes
1. The values of the yield strength are those of the 0.2% yield strength for products that do not present a definite yield point, and the lower yield strength ReL for the other products.
2. For a thickness of 0.5 mm < t < 0.7 mm the maximum value of the yield strength is increased by 20 N/mm² and the minimum elongation after fracture is decreased by 2%.
3. For a thickness of t ≤ 0.5 mm the maximum value of the yield strength is increased by 40 N/mm² and the minimum elongation after fracture is decreased by 4%.
   Elongation after fracture A uses test piece length L0 = 80 mm.
4. The r value applies to a thickness of t ≥ 0.5 mm.
   For a thickness of t > 2 mm, the r value is decreased by 0.2.
5. For a thickness of t ≥ 1.5 mm the maximum value of the yield strength is 225 N/mm².
6. For design purposes, a lower yield strength ReL of at least 120 N/mm² can be assumed.
 

Chemical composition

Tata Steel complies with the following cast analysis:

Tata Steel Ymvit Grade Ymvit Extra 06
EN 10209: 2013 Grade DC06ED
C Max. 0.004
Mn Max. 0.35
P Max. 0.020
S Max. 0.050
Ti Max. 0.30
The elements P and Cu are kept within certain limits to ensure that the reactivity of the steel surface is as constant as possible. Under normal conditions this leads to a reproducible enamelling result.
All values are in weight%.

EN-Engineering-Product-Cold-rolled-Ymvit enamelling-Ymvit Extra 06-Dimensions TSN

Dimensions

Dimensional capability

Dimensions in mm.

Thickness Max. width
From - up to Ymvit Extra 06
0.40 - 0.50 1820
0.50 - 0.60 1950
0.60 - 0.70 1980
0.70 - 0.80 1990
0.80 - 1.50 2010
1.50 - 1.60 1950
1.60 - 1.70 1850
1.70 - 1.80 1750
1.80 - 1.90 1660
1.90 - 2.00 1570
2.00 - 2.10 1500
Minimum width is 900 mm.
Other dimensions are available on request – please contact us for details.
 

Tolerances

Tolerances comply with standard EN 10131: 2006.
Tighter tolerances are available, please contact us for details.

EN-EngineeringAutomotive-Product-Cold-rolled-All Grades Shape and Dimensional TolerancesTSE

Shape and dimensional tolerances

Tolerances on shape and dimensions comply with standard EN 10131: 2006

 

Tolerances on thickness

Tolerance (EN 10131: 2006)

Availability

Full thickness tolerance

Available

Special thickness tolerances

Available

50% of full thickness tolerance

Refer before ordering

Tolerances closer than special tolerances may be agreed at the time of enquiry.
Tolerances in mm.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re < 260N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.03

± 0.04

± 0.05

± 0.020

± 0.025

± 0.030

> 0.40

≤ 0.60

± 0.03

± 0.04

± 0.05

± 0.025

± 0.030

± 0.035

> 0.60

≤ 0.80

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.80

≤ 1.00

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 1.00

≤ 1.20

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.20

≤ 1.60

± 0.08

± 0.09

± 0.10

± 0.050

± 0.060

± 0.070

> 1.60

≤ 2.00

± 0.10

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 2.00

≤ 2.50

± 0.12

± 0.13

± 0.14

± 0.080

± 0.090

± 0.100

> 2.50

≤ 3.00

± 0.15

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength 
260 N/mm2 ≤ Re < 340N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.025

± 0.030

± 0.035

> 0.40

≤ 0.60

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.60

≤ 0.80

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.80

≤ 1.00

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 1.00

≤ 1.20

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.20

≤ 1.60

± 0.09

± 0.11

± 0.12

± 0.060

± 0.070

± 0.080

> 1.60

≤ 2.00

± 0.12

± 0.13

± 0.14

± 0.070

± 0.080

± 0.100

> 2.00

≤ 2.50

± 0.14

± 0.15

± 0.16

± 0.100

± 0.110

± 0.120

> 2.50

≤ 3.00

± 0.17

± 0.18

± 0.18

± 0.120

± 0.130

± 0.140

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
340N/mm2 ≤ Re ≤ 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.04

± 0.05

± 0.06

± 0.030

± 0.035

± 0.040

> 0.40

≤ 0.60

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.60

≤ 0.80

± 0.06

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.80

≤ 1.00

± 0.07

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 1.00

≤ 1.20

± 0.09

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.20

≤ 1.60

± 0.11

± 0.12

± 0.14

± 0.070

± 0.080

± 0.100

> 1.60

≤ 2.00

± 0.14

± 0.15

± 0.17

± 0.080

± 0.100

± 0.110

> 2.00

≤ 2.50

± 0.16

± 0.18

± 0.19

± 0.110

± 0.120

± 0.130

> 2.50

≤ 3.00

± 0.20

± 0.20

± 0.21

± 0.130

± 0.140

± 0.150

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on thickness for steel grades with a specified minimum yield strength
Re > 420N/mm2.

Nominal
thickness

Normal tolerances for a nominal width of 1

Special tolerances (S) for a
nominal width of 1 2

 

≤ 1200

> 1200

> 1500

≤ 1200

> 1200

> 1500

 

≤ 1500

 

 

≤ 1500

 

≥ 0.35

≤ 0.40

± 0.05

± 0.06

± 0.07

± 0.035

± 0.040

± 0.050

> 0.40

≤ 0.60

± 0.05

± 0.07

± 0.08

± 0.040

± 0.050

± 0.060

> 0.60

≤ 0.80

± 0.06

± 0.08

± 0.10

± 0.050

± 0.060

± 0.070

> 0.80

≤ 1.00

± 0.08

± 0.10

± 0.11

± 0.060

± 0.070

± 0.080

> 1.00

≤ 1.20

± 0.10

± 0.11

± 0.13

± 0.070

± 0.080

± 0.100

> 1.20

≤ 1.60

± 0.13

± 0.14

± 0.16

± 0.080

± 0.100

± 0.110

> 1.60

≤ 2.00

± 0.16

± 0.17

± 0.19

± 0.100

± 0.110

± 0.130

> 2.00

≤ 2.50

± 0.19

± 0.20

± 0.22

± 0.130

± 0.140

± 0.160

> 2.50

≤ 3.00

± 0.22

± 0.23

± 0.24

± 0.160

± 0.170

± 0.180

1. Around cold-rolled welds - the pickling welds - an increase of 20% at the most over the thickness
   is allowed over a length of 15 metres.
2. For special tolerances, not all combinations of thickness and width are available in every product.
   Please contact us for more details.

 

Tolerances on width

Tolerance 
(EN 10131: 2006)

Availability

Normal width tolerances

Available

Special width tolerances

Refer (± 0.50 mm available on 750 - 2000 mm width)

 

Nominal width w

Normal tolerances

Special tolerances (S)

 

Under

Over

Under

Over

w ≤ 1200

0

4

0

2

1200 < w ≤ 1500

0

5

0

2

w > 1500

0

6

0

3

 

Out-of-squareness (products supplied as cut sheets only)

The deviation does not exceed 1% of the actual width of the sheet according to the EN 10131: 2006 standard. The deviation from the edge camber does not exceed 5mm for a length of 2 metres as specified in EN 10131: 2006.

 

Flatness (products supplied as skin-passed cut sheets only)

Flatness complies with EN 10131: 2006
If there is a dispute about the flatness of material that was ordered to the special tolerances shown in table 8 of EN 10131: 2006, then the minimum acceptable standards of flatness described below must be verified.
Criteria in case of disputes over special (FS) flatness tolerances (ReL < 260 N/mm2)

Dimensions in mm.

Nominal width

Edge-wave length

Maximum acceptable wave height

< 1500

> 200

< 1% of edge-wave length

≥ 1500

> 200

< 1.5% of edge-wave length

< 200

 2mm

 

Winding

For winding, there may be a maximum width gap of 3mm between two con­se­cutive windings. The total width stagger across the coil wall will not exceed 10mm.

 

Dimensions and coil weights

Tata Steel can supply cold-rolled steel with the following minimum and maximum dimensions and coil weights.

Description Availability
Coil diameter inner 610mm
(508mm available on request)
Coil diameter outer 10/7 x width max
1000mm min.
2800mm max.
Coil weight 30 t max.
30 - 45 t max available after consultation
Coil weight limited by maximum outer diameter
Maximum weight allowed by road/rail transport
Some products may have different coil weight ranges available
Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
KIM: width ≤ 1200mm 11.9 - 21.5 kg/mm width
KIM: 1200mm < width ≤ 1700mm 11.9 - 21 kg/mm width
KIM: width > 1700mm 10.3 kg/mm width and 11.9 - 21 kg/mm width
Minimum tonnage per order Refer to price list for order quantity details
Minimum order quantities may apply

 

 

Coil welds

For batch-annealed coils, in general, pickling line welds are included. The number of permissible recoiling line welds is determined in consultation with the customer. If welds are permitted, Tata Steel is better able to implement the best coil weight. A recoiling line weld is marked with a single hole in the centre of the strip, close to the weld. On request the identifying hole can be left out. Coils with welds are available on continuously-annealed products – please contact us for details. You can find details on how to get in touch with us in 'Contact Us' below.

 

EN-EngineeringAutomotive-Product-Cold-rolled-All grades Further processingTSE

Further processing

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type Slitting Decoiling Blanking
Thickness range (mm) 0.2 - 7.0 0.3 - 6.0 0.3 - 6.0
Width range (mm) 10 - 2050 50 - 2600 200 - 2600
Length range - up to 6m up to 6m
Locations UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Ireland
Netherlands
Germany
France
Spain
Sweden
Norway
Finland
UK
Netherlands

 

For further information please visit our Service Centre webpages.