Ympress S500MC
Specification details for Ympress S500MC

EN-Automotive-Product-Hot-Rolled-HSS-All grades Overview TSE

Overview

Our high-strength steel grades have been developed to meet a wide variety of applications. The consistent quality of these steels means they can be relied on to deliver benefits for your end-products and processes.

The high yield strength of Ympress delivers weight savings and increased component strength. This can help you create lighter, stronger products and increase yield through down-gauging. Consistent properties and tight control of material thickness allow trouble-free, repeatable processing. Ympress can be easily welded and galvanised. Its high surface quality can lead to fewer processing steps.

Applications

 

Relationship with standards

Tata Steel’s high-strength low-alloy steels comply with the following standards:
 

VDA EN 10149-2:2013 Tata Steel Tata Steel
Grade Grade Grade Grade
HR300LA S315MC Ympress S315MC XF315
HR340LA S355MC Ympress S355MC XF355
HR420LA S420MC Ympress S420MC XF420
HR460LA S460MC Ympress S460MC XF460
HR500LA S500MC Ympress S500MC XF500
- S550MC Ympress S550MC -
- S650MC Ympress S650MC -
- - Ympress E690TM -
HR700LA S700MC Ympress S700MC -
HR960LA S960MC Ympress S960MC -

 

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition

non-pickled

pickled

pickled and oiled

Mill edges

Yes

Yes

Yes

Trimmed edges

-

Yes

Yes

Trimmed edges available in thicknesses up to 8.0 mm. The steel grades shown on the following pages belong to the standard range offered by Tata Steel.
Please contact us regarding other specifications we may have that meet your needs.
 

Surface aspects

Description

Availability

Surface finish

Coils are available in non-pickled and pickled finish

Oiling

Pickled finish is available with rolling or preservative oil applied

 

Oil weight normally 0.5-2.5 g/m2

Alternative oiling ranges are available – please contact us for details.

EN-EngineeringAutomotive-Product-Hot-rolled-All Grades Surface aspects Supply Conditions TSE

Supply Conditions

Supply - product conditions

Hot-rolled steel can be supplied with these product conditions and finishes and with this surface treatment:

Side/surface condition non-pickled pickled pickled and oiled
Mill edges Yes Yes Yes
Trimmed edges - Yes Yes
Trimmed edges available in thicknesses up to 8.0 mm.
Please contact us regarding other specifications we may have that meet your needs.
 

Surface aspects

Description Availability
Surface finish Coils are available in non-pickled and pickled finish for most grades. 
For grade specific availability, please refer to the dimensional tables.
Oiling Pickled finish is available with rolling
or preservative oil applied. 
Oil weight normally 0.5-2.5 g/m2
Alternative oiling ranges are available.
Please contact us for details.
 

Certification

Test certificates 2.2/3.1 are available according to EN 10204.         

EN-EngineeringAutomotive-Product-Hot-Rolled-HSS-Ympress S500MC-Properties TSN

Properties

Mechanical Properties

Steel supplied will comply with the mechanical property limits below.
The values of the tensile test apply to test bars parallel to the rolling direction. 
The values of the bend test apply to test bars transverse to the rolling direction.

Tata Steel Grade Ympress S500MC
Min. Yield strength  ReH1 (N/mm²)   500
Tensile strength Rm (N/mm²)   580 - 700
Elongation (%) t < 3 13
3 ≤ t < 5 18
t ≥ 5 17
Min. bend test diameter t < 5 0.5 t
t ≥ 5 0.5 t
1. Upper yield strength or 0.2% proof stress applies.
t – material thickness in mm.
Elongation after fracture A uses test piece length L0 = 80 mm for t < 3 mm. L0 = 5.65√S0 for t ≥ 3 mm.

Impact strength

Impact tests can be performed for thicknesses ≥ 6.0 mm. Please contact us for details.


Chemical composition

Steel supplied will comply with the chemical limits below

Tata Steel Grade Ympress S500MC
C Max. 0.1
Mn Max. 1.65
P Max. 0.02
S Max. 0.003
Si Max. 0.03
Altot Min. 0.015
Nb Max. 1 0.08
V Max. 1 -
Ti Max. 1 0.06
Mo Max. -
Cu Max. -
1. The sum of Nb, V and Ti shall be max. 0.22%.
All values are in weight%

EN-Automotive-Product-Hot-Rolled-HSS-Ympress S500MC-Dimensions TSN

Dimensions

Dimensional capability - pickled

Dimensions in mm. These dimensions are applicable to both the Ympress and the EN equivalent grades unless noted otherwise.
 

Thickness  Max. width
From - up to Ympress S500MC
1.70 - 1.80 920
1.80 - 1.90 1030
1.90 - 2.00 1100
2.00 - 2.20 1180
2.20 - 2.40 1300
2.40 - 2.60 1420
2.60 - 2.80 1540
2.80 - 3.00 1650
3.00 - 3.20 1710
3.20 - 3.47 1740
3.47 - 3.65 1780
3.65 - 4.00 1800
4.00 - 4.40 1850
4.40 - 5.00 1900
5.00 - 5.60 2000
5.60 - 8.10 2070
The minimum width is 1000 mm.
Higher max. widths are available for some non-Ympress grades, please contact us for more information.
Widths smaller than 1000 mm and/or thicknesses up to 20 mm may be available - please contact us.
Non-pickled (dry) condition is also available.
 

Tolerances

Tolerances for wide strip and slit wide strip comply with standard EN 10051: 2010.

Tighter tolerances are available, please contact us.

 

EN-EngineeringAutomotive-Product-Hot-rolled-All grades Shape and dimensional tolerances TSE

Shape and dimensional tolerances

Shape and dimensional tolerances

The specified values for wide strip do not apply to the uncropped ends of the coil (‘head’ and ‘tail’). The length of these uncropped ends is calculated using the following formula:

length (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres.

If required, this part of the coil can be removed, however an additional cost may be charged for this.

 

Tolerances on thickness

Tata Steel can supply to full thickness tolerance specified in EN 10051:2010.

Tighter tolerances are available as shown below:

Product type Thickness tolerances available
  (% of full EN 10051:2010 tolerance)
  100% 75% 66% 60% 50% 33%

Steel for forming

Yes

Yes

Yes

Yes

Yes

Yes 1

High-strength low-alloy
(HSLA EN 10149-2)

Yes

Yes

Yes

Yes

Yes

Yes 1

Ympress® HSLA

 

 

 

 

Yes

Yes 1

Ympress® Laser

 

 

 

 

Yes

Yes 1

Structural steel

Yes

Yes

Yes

Yes

Yes

Yes 1

Boron manganese steel Yes Yes Yes Yes Yes  

Case-hardening steel

Yes

Yes

Yes

Yes

Yes

 

High-carbon steel

Yes

 

 

 

 

 

Dual phase steel

Yes

 

 

 

 

 

Hot forming steel

Yes

 

 

 

 

 

Valast® abrasion resistant steel

Yes

Yes

Yes

Yes

Yes

 

Steel for pressure vessels

Yes

 

 

 

 

 

Steel for gas cylinders

Yes

 

 

 

 

 

Steel for line pipe

Yes

 

 

 

 

 

Ship plate

Yes

 

 

 

 

 

1. Available for certain grades and thicknesses between 3.0mm and 6.0mm.
Please contact us on the availability of special tolerances to meet your requirements.
 
Tolerances on thickness for hot-rolled steel with a low carbon content for cold forming
(DD11-DD14 in EN 10111:2008)